Author Topic: Vibrating or rattling noise?????  (Read 4793 times)

Offline MEK-Dangerfield

  • C-C.com Expert
  • ********
  • Posts: 20946
  • I don't get NO respect! Member since 1/25/2002
Re: Vibrating or rattling noise?????
« Reply #30 on: July 16, 2006 - 11:49:04 AM »
I think your timing would have to be WAAAY off to cause backfiring. As Goody said, what do your plugs look like. Maybe your carb. is running toooooo lean.

  Mike

Mike

1970 Challenger - SOLD
2016 SXT+.  1 of 524 SXT+'s in Plumb-crazy for 2016.




Offline JRoss22

  • Jr. Member
  • **
  • Posts: 458
  • Member Since 05/08/2005
Re: Vibrating or rattling noise?????
« Reply #31 on: July 16, 2006 - 11:50:11 AM »
That could be why I didnt get the choke hooked up... I remember that now because for some reason it just didnt want to hook up properly.... That could deff be my issue thanks for pointing that out....

Offline ShelbyDogg

  • Sr. Resident
  • ******
  • Posts: 5007
Re: Vibrating or rattling noise?????
« Reply #32 on: July 16, 2006 - 10:43:29 PM »
JRoss22,   Backfiring could be caused by the spark plug wires being on the wrong cylinders or a burnt/stuck valve.   Check your firing order first.

Rob
Rob

3 E-bodies, Megasquirt-1v3.0, Edelbrock Pro-Flo-1, Holley C950, FAST EZ-EFI; say no to carbs...yes to throttle bodies

My Pace Car restoration thread:
http://www.cuda-challenger.com/cc/index.php?topic=44869.0


Offline JRoss22

  • Jr. Member
  • **
  • Posts: 458
  • Member Since 05/08/2005
Re: Vibrating or rattling noise?????
« Reply #33 on: July 16, 2006 - 10:45:41 PM »
I know the firing order is correct when I did the tune up on it I had the manual in front of me to make sure I got everything hooked back up properly... I am going to check it out again and maybe pull the valve covers and see if i can find something wrong if not I might just end up tearing down the block for a rebuild....

Offline GoodysGotaCuda

  • Sr. Resident
  • ******
  • Posts: 5392
Re: Vibrating or rattling noise?????
« Reply #34 on: July 16, 2006 - 10:52:51 PM »
I know the firing order is correct when I did the tune up on it I had the manual in front of me to make sure I got everything hooked back up properly... I am going to check it out again and maybe pull the valve covers and see if i can find something wrong if not I might just end up tearing down the block for a rebuild....



In all honesty i've done that myself. i had the book and did it 'correct'. and sure enough there was a issue and i had to go back and i had screwed it up. lol. Takes 2minutes to recheck it, and its not uncommon that you screw it up once or twice in your tinkering/tuning days  :smilielol:

http://www.boxwrench.net/specs/schrys_A.htm

Backfiring would be timing, too lean? that'd lead to pinging, and misfiring/crossed wires.

Build Page: Goody's 'Cuda Build Page
1976 Dodge Warlock
1972 Barracuda - 5.7 Hemi + T56 Magnum

Wheel & Tire Specs:Link

Offline JRoss22

  • Jr. Member
  • **
  • Posts: 458
  • Member Since 05/08/2005
Re: Vibrating or rattling noise?????
« Reply #35 on: July 16, 2006 - 10:57:04 PM »
Thanks Goody for that link saved to my comp and gonna print it up next time I go down stairs to my parents comp to print stuff... And I will double check all the spark plugs and everything when I get the chance

Offline ntstlgl1970

  • Resident
  • *****
  • Posts: 2204
  • T a c o c a t
Re: Vibrating or rattling noise?????
« Reply #36 on: July 22, 2006 - 08:47:26 PM »
Depending on where you are in Roseville, I would be willing to take a look at it and see if I can help.....
70 Cuda, 7.0L Gen-III Hemi, Viper T56 w/9310 gearset, 3.91's, Megasquirt MS3x v3.57, Innovate wideband, Firm Feel upper arms, torsion bars, springs and strut rods, QA1 DA shocks. I did everything on this car except the fancy paint stuff and I drive it...and I can't seem to stop messing with it....

Offline JRoss22

  • Jr. Member
  • **
  • Posts: 458
  • Member Since 05/08/2005
Re: Vibrating or rattling noise?????
« Reply #37 on: July 22, 2006 - 09:31:08 PM »
I am over by woodcreek. Do you know where that is?

Offline ntstlgl1970

  • Resident
  • *****
  • Posts: 2204
  • T a c o c a t
Re: Vibrating or rattling noise?????
« Reply #38 on: July 23, 2006 - 12:04:28 AM »
I'm not familiar with woodcreek, but I lived in Citrus Heights for a while, if you can give me some cross streets I'm sure I could figure it out.

70 Cuda, 7.0L Gen-III Hemi, Viper T56 w/9310 gearset, 3.91's, Megasquirt MS3x v3.57, Innovate wideband, Firm Feel upper arms, torsion bars, springs and strut rods, QA1 DA shocks. I did everything on this car except the fancy paint stuff and I drive it...and I can't seem to stop messing with it....