News:

  • Home
  • Help
  • Chat
  • Login
  • Register

    • « previous next »
    Pages: 1 [2]

    Author Topic: 71 Barracuda East Coast  (Read 7201 times)

    Offline HP_Cuda

    • Hit the skinny little pedal on the right!
    • Sr. Resident
    • ******
    • Posts: 5268
    • Mopar or No Car!
    Re: 71 Barracuda East Coast
    « Reply #15 on: January 03, 2016 - 04:32:31 PM »

    Dodj

    Check out my build thread, you will be surprised! But in the end, I could have paid more for a more intact car but would have ended up paying the same.

    Six of this, half dozen of that.

    B

    Quote from: dodj on January 03, 2016 - 03:42:02 PM
    Wow! What didn't you replace?!? The ash tray?
    Logged
    1970 Cuda Clone 440 4 speed - sublime green
    1970 Cuda 383 4 speed - yellow - SOLD


    Offline nicka

    • Jr. Member
    • **
    • Posts: 53
    Re: 71 Barracuda East Coast
    « Reply #16 on: June 26, 2016 - 05:31:36 PM »
    Built a body roller so i can move it out back into my workshop.  Accumulated some AMD sheetmetal while at the shows.  Looks like a fall startup.  Thinking about building a body cart.
    Logged

    Offline nicka

    • Jr. Member
    • **
    • Posts: 53
    Re: 71 Barracuda East Coast
    « Reply #17 on: April 02, 2018 - 09:21:37 PM »
    Back on the Barracuda.  Building a jig/table.
    Logged

    Offline nicka

    • Jr. Member
    • **
    • Posts: 53
    Re: 71 Barracuda East Coast
    « Reply #18 on: April 02, 2018 - 09:26:51 PM »
    Working on a jig/table over the winter.
    Logged

    Offline 70chall440

    • Sr. Resident
    • ******
    • Posts: 6484
    Re: 71 Barracuda East Coast
    « Reply #19 on: April 02, 2018 - 11:03:06 PM »
    Pretty nice
    Logged
    Current Mopar
    70 Challenger RT 440-6 EFI, 73 Cuda 416-6 EFI
    05 Hemi Durango, 01 Ram 4x4, 14 Ram 2500 4X4, 10 PCP Challenger 6 spd RT, 01 Viper GTS ACR, 52 B3B w/330 Desoto Hemi, 70 Hemi RR (under const)
    Past Mopars
    9 x Challengers. AAR Cuda, 4 RR, 2 GTX, 4 Chargers, etc... (too many to list)

    Offline Cuda416

    • Jr. Member
    • **
    • Posts: 193
    Re: 71 Barracuda East Coast
    « Reply #20 on: April 23, 2018 - 02:45:47 PM »
    Quote from: nicka on April 02, 2018 - 09:26:51 PM
    Working on a jig/table over the winter.

    Couple of things...

    1. Nice jig!

    2. Is it parallel or did you make the "front" a bit narrow?

    3. Are you building "standoffs" for it?

    Finally, very creative solution to getting the car up onto it without a lift!
    Logged
    70' Barracuda conv. (project)

    Offline nicka

    • Jr. Member
    • **
    • Posts: 53
    Re: 71 Barracuda East Coast
    « Reply #21 on: May 02, 2018 - 08:50:40 PM »
    On the table.
    Logged

    Offline nicka

    • Jr. Member
    • **
    • Posts: 53
    Re: 71 Barracuda East Coast
    « Reply #22 on: May 02, 2018 - 08:57:18 PM »
    The widest portion of the barracuda frame rail is 49" which is the rear frame rail, so the table/jig is 49" wide from front to back.

       
    Nick
    Logged

    Offline 340challconvert

    • Jr. Member
    • **
    • Posts: 497
    • A66- Challenger Registry
      • A66CHALLENGER.COM
    Re: 71 Barracuda East Coast
    « Reply #23 on: July 28, 2018 - 11:54:22 AM »
    Nice jig and good luck with the work.
    You are tackling a lot of sheet metal work; good for you
    I'm worrying about just replacing my trunk floor and only part of the driver's side front floor pan
    Logged
    1970 Challenger A66 Registry
    Pages: 1 [2]
    « previous next »