Author Topic: Front window trim question 70 Cuda (Read 1718 times)

HP_Cuda · « **on:** August 31, 2012 - 01:24:01 PM »

I have a dumb question because I believe I already know the answer but does the lower flat piece of the front window trim get a gasket before mating with the body? I know it leverages a couple of bolts from the windshield wiper mechanism.

If anyone has a pic of the lower trim piece with the hood up that would be awesome!

Thanks,
Bryan

burdar · « **Reply #1 on:** August 31, 2012 - 02:55:54 PM »

No gasket. It uses two wiper bolts like you said. Then the factory put a few blobs of sealer under it to hold it tight on the top side. The corner pieces need some strip caulk around the attaching screws so you don't get a leak.

HP_Cuda · « **Reply #2 on:** August 31, 2012 - 03:32:45 PM »

Perfect! Now I need to know if the corner pieces are bolted to the car with machine screws?

I see no holes so I guess I'll have to make them...

Thanks a ton!
Bryan

burdar · « **Reply #3 on:** August 31, 2012 - 03:43:41 PM »

Mine are held on with chrome philips head screws. They have a built-in washer on them. There are slots where the screws attach...it isn't just a small hole. That's why you need some strip caulk around the screw. Water will leak in through the slot if it isn't sealed up.

HP_Cuda · « **Reply #4 on:** August 31, 2012 - 03:58:05 PM »

So its screw and bolt thru the firewall?

burdar · « **Reply #5 on:** August 31, 2012 - 04:09:44 PM »

The corner pieces are just held on with a screw into the cowl. It doesn't screw into a hole...it screws into a slot. Just like how the inside rear window trim screws are thread into slotts...not holes.

HP_Cuda · « **Reply #6 on:** August 31, 2012 - 05:58:39 PM »

As you can see from the pic I don't see any slots in this area to put a screw through. Hmmm it's a new firewall so it may not have them?

burdar · « **Reply #7 on:** August 31, 2012 - 06:43:40 PM »

Originally, there would have been a slot dirrectly under the trim hole. The slot allows for some production tolerance stack-up. If the cowl is new then it could be missing the slot.

HP_Cuda · « **Reply #8 on:** August 31, 2012 - 06:46:28 PM »

Hmm well unless I want to remove the front fender and drill a slot I'm sh*t out of luck.

Any ideas?

burdar · « **Reply #9 on:** August 31, 2012 - 07:56:43 PM »

Stick a pick through the trim hole when it's in the correct location and mark the spot to drill. It looks like you have plenty of room.

HP_Cuda · « **Reply #10 on:** August 31, 2012 - 11:08:18 PM »

To get a straight up and down hole it will br close to the fender but doable.

Thanks for all the help!
Bryan

Author Topic: Front window trim question 70 Cuda (Read 1718 times)

HP_Cuda

Front window trim question 70 Cuda

burdar

Re: Front window trim question 70 Cuda

HP_Cuda

Re: Front window trim question 70 Cuda

burdar

Re: Front window trim question 70 Cuda

HP_Cuda

Re: Front window trim question 70 Cuda

burdar

Re: Front window trim question 70 Cuda

HP_Cuda

Re: Front window trim question 70 Cuda

burdar

Re: Front window trim question 70 Cuda

HP_Cuda

Re: Front window trim question 70 Cuda

burdar

Re: Front window trim question 70 Cuda

HP_Cuda

Re: Front window trim question 70 Cuda