Author Topic: Mopar Street Car Specs and E.T.s. 10.99 - 9.99  (Read 6175 times)

Offline Oldschool

  • Administrator
  • Permanent Resident
  • *****
  • Posts: 13195
  • Member Since 9-05-06
Mopar Street Car Specs and E.T.s. 10.99 - 9.99
« on: October 29, 2010 - 12:07:29 PM »
Please post your Mopar combo here if your street car runs the 1/4 mile between 9.99 - 10.99.    :burnout:   
Ken  --  In Georgia

MOPAR-------"Built To Run------Here To Stay"




Offline StRoKeR

  • Jr. Member
  • **
  • Posts: 49
Re: Mopar Street Car Specs and E.T.s. 10.99 - 9.99
« Reply #1 on: December 03, 2010 - 06:19:39 PM »
My old 72 Challenger



Basic Rundown
3850lbs race ready
Raced on 93 PUMP GAS
Caltracs Suspension
Dana 60
4.10 gears
315/60/15 ET Street Radials
3.5" exhaust
Full interior
727 tranny
Be cool rad system

Engine
Naturally Aspirated
440(stock block girdled/ARP studded) stroked to 500CI
Mopar Crank 4.150" / Manley rods 6.760"
Comp roller cam XR286R (cam lift was .660 with the 1.7's)
Harland Sharp 1.7 rockers
TTI 2" Headers
Indy EZ Heads MW CNC 2.19/1.81 Ferrea valves
Indy 440-3 Intake (ported by me)
Custom BIGS 1050 Dominator
Pete Jackson Noisy Gear Drive
JE Pistons
Comp roller lifters
11 to 1 compression
MSD electronics

Best Performance
MPH 101.00 1/8
MPH 128.38 1/4
ET 6.80 1/8
ET 10.67 1/4 (2400 DA & only time out on new setup)

Only vid I got left of her! She ran great on the street...  :burnout:

Dodge Challenger 500" N/A Pump Gas


« Last Edit: October 06, 2012 - 10:50:36 AM by -Sledgehammer- »
Member Since January 14, 2004

71' Dart - 9 second All Motor Pump Gas Street Car! Full Interior, Full Exhaust, Raced on Local 93! 3400lbs.

72' Challenger - 10.67 @ 127.78 All Motor on 93 pump gas! 3850lb street car (SOLD)

Offline KellysCuda aircard

  • Its good to be blown
  • Full Member
  • ***
  • Posts: 868
Re: Mopar Street Car Specs and E.T.s. 10.99 - 9.99
« Reply #2 on: December 03, 2010 - 06:55:38 PM »
Hi Ken, well we put a 540 ( 440 source) in her last summer and got her down to a uncorrected 10-40 with a 1.47 60 foot time at a 129mph.
There is more there but I am starting to beat the car up, lots of welding went back in this spring, I think I am gonna tube chassis the car.

Offline The Cuda Guy

  • Support Our Troops
  • Resident
  • ****
  • Posts: 3899
  • Pearl Harbor, HI
    • C-C.com
Re: Mopar Street Car Specs and E.T.s. 10.99 - 9.99
« Reply #3 on: December 04, 2010 - 06:39:34 AM »
My old 72 Challenger




Basic Rundown
3850lbs race ready
Raced on 93 PUMP GAS
Caltracs Suspension
Dana 60
4.10 gears
315/60/15 ET Street Radials
3.5" exhaust
Full interior
727 tranny
Be cool rad system

Engine
Naturally Aspirated
440(stock block girdled/ARP studded) stroked to 500CI
Mopar Crank 4.150" / Manley rods 6.760"
Comp roller cam XR286R (cam lift was .660 with the 1.7's)
Harland Sharp 1.7 rockers
TTI 2" Headers
Indy EZ Heads MW CNC 2.19/1.81 Ferrea valves
Indy 440-3 Intake (ported by me)
Custom BIGS 1050 Dominator
Pete Jackson Noisy Gear Drive
JE Pistons
Comp roller lifters
11 to 1 compression
MSD electronics

Best Performance
MPH 101.00 1/8
MPH 128.38 1/4
ET 6.80 1/8
ET 10.67 1/4 (2400 DA & only time out on new setup)

Only vid I got left of her! She ran great on the street...  :burnout:

http://www.youtube.com/watch?v=gz-szQ1yrgY


Ok... so my new goal is to run a 10.6     LOL!!!

That was a bad a$$ chally bro! 

Don


 :aarg: 
The Cuda Guy Project is on going!

Member Since January 14, 2002