Author Topic: Question about car height  (Read 1133 times)

Offline dlrogers

  • Jr. Member
  • **
  • Posts: 134
  • 1971 Challenger 383
Question about car height
« on: May 22, 2006 - 02:38:11 AM »
Hi all
I noticed that the height of my chally at the front end differs from side to side in that the left front is about 2cm lower than the right - the left front fender covers about 2cm more of the tyre than the other side so it's not tyre pressure. I don't think its the shocks in the front but was wondering if the torsion bars may be affecting things?? Any thoughts??

David
Bay of Islands, New Zealand




Offline MEK-Dangerfield

  • C-C.com Expert
  • ********
  • Posts: 20946
  • I don't get NO respect! Member since 1/25/2002
Re: Question about car height
« Reply #1 on: May 22, 2006 - 03:20:58 AM »
Yep,
  If it isn't a shock crapping out on you, then I would guess it's a torsion bar needing adjustment. I guess you need to decide if you want to lower one side, or raise the other.

  Mike

Mike

1970 Challenger - SOLD
2016 SXT+.  1 of 524 SXT+'s in Plumb-crazy for 2016.

Offline dlrogers

  • Jr. Member
  • **
  • Posts: 134
  • 1971 Challenger 383
Re: Question about car height
« Reply #2 on: May 22, 2006 - 04:29:41 AM »
Yea, thanks Mike, thats about what I thought.
David
Bay of Islands, New Zealand

Offline ShelbyDogg

  • Sr. Resident
  • ******
  • Posts: 5007
Re: Question about car height
« Reply #3 on: May 22, 2006 - 08:49:33 AM »
Make sure that your rear springs are causing it to look that way.    In my race car, I would preload right side rear so the car would lean left.  To compensate I would adjust the left front to make it sit level again.

To eliminate the rear suspension, you can use a 4x4 going across the rear frame, then jack it up right in the center. Then you can adjust the torsion bars to equal them out.

Rob
« Last Edit: May 22, 2006 - 08:51:38 AM by shelbydogg »
Rob

3 E-bodies, Megasquirt-1v3.0, Edelbrock Pro-Flo-1, Holley C950, FAST EZ-EFI; say no to carbs...yes to throttle bodies

My Pace Car restoration thread:
http://www.cuda-challenger.com/cc/index.php?topic=44869.0


Oldschool

  • Guest
Re: Question about car height
« Reply #4 on: May 22, 2006 - 04:18:52 PM »
After you get em evened back out, don't forget to have the alignment re-checked......   :grinyes: 

Offline Chryco Psycho

  • Administrator
  • C-C.com Guru
  • *****
  • Posts: 36620
  • 70 Challenger R/T SE 70 tube Chassis Cuda now sold
Re: Question about car height
« Reply #5 on: May 22, 2006 - 10:57:47 PM »
or check it with a tape measure

Challenger - You`ll wish You Hadn`t

Offline dlrogers

  • Jr. Member
  • **
  • Posts: 134
  • 1971 Challenger 383
Re: Question about car height
« Reply #6 on: May 23, 2006 - 01:16:32 AM »
Thanks for the advice everyone
David
Bay of Islands, New Zealand

Offline Chryco Psycho

  • Administrator
  • C-C.com Guru
  • *****
  • Posts: 36620
  • 70 Challenger R/T SE 70 tube Chassis Cuda now sold
Re: Question about car height
« Reply #7 on: May 23, 2006 - 12:30:42 PM »
make sure you take the weight off the front end of the car before adjusting the T bars

Challenger - You`ll wish You Hadn`t