Home
Member Rides
Forum
Sponsor Sites
Tools
Contact
News:
Home
Help
Search
Chat
Login
Register
Cuda-Challenger.com
»
Chryco's Tech Shop
»
The Body Shop
(Moderator:
Chryco Psycho
) »
hood alignment issues
« previous
next »
Print
Pages: [
1
]
Author
Topic: hood alignment issues (Read 1308 times)
focal 7
Jr. Member
Posts: 114
hood alignment issues
«
on:
October 09, 2006 - 11:12:48 PM »
I'm having trouble getting the hood to line up on a 74 chally I'm putting back together. Any suggestions on what to do first??? Evertime I change something 1 thing gets better, but 2 get worse. The main problem is that the back hood corners on both sides just set too high when the hood is closed. Is there an order I should go in??? Thanks in advance for any and all help!
Logged
PlumCrazy
Jr. Member
Posts: 349
Re: hood alignment issues
«
Reply #1 on:
October 09, 2006 - 11:31:24 PM »
You need to adjust the hood hinges on the inner fender upward, and the snug them just tight. Then lift the hood and loosen the rear bolts and rotate the hinge as viewed from the side, tighten the bolts and check the fit. Repeat until you get the alignment right.
Logged
Chryco Psycho
Administrator
C-C.com Guru
Posts: 36620
70 Challenger R/T SE 70 tube Chassis Cuda now sold
Re: hood alignment issues
«
Reply #2 on:
October 10, 2006 - 01:22:32 AM »
this works opposite to what you think will work ,basically as above , loosen the hinge bolts & have someone lift the front of the hood & keep lifting until the hinges move then snug the hinges down & try closing the hood , I hope this is a clearer way to explain it
Logged
Challenger - You`ll wish You Hadn`t
4Cruizn
Administrator
C-C.com Expert
Posts: 18521
HEMI FISH
Re: hood alignment issues
«
Reply #3 on:
October 10, 2006 - 11:01:11 AM »
I would use tape to protect the edges until I got the hood on there straight.
Logged
miketyler
Resident
Posts: 2561
Re: hood alignment issues
«
Reply #4 on:
October 10, 2006 - 01:00:05 PM »
I had similar fit issues. I have acceptable gaps all the way around but the aft drivers side corner still wants to stay slightly up. YOu can push it down once closed but it still isnt right. I had played with the adjustments quite a bit and had assumed my drivers hinge may be worn. I had to remove my hood to prep and paint the underside. I'll reference this thread when I reinstall. I hate to replace the hinges as they have both been chromed.
MRT
Logged
72' Cuda restomod
70 Mustang Mach 1
07' Toyota Tacoma Prerunner Dbl cab in Speedway Blue!
01' Honda 1100 Shadow Sabre
96' Seadoo Challenger
Wang
Full Member
Posts: 993
"just hangin' out"
Re: hood alignment issues
«
Reply #5 on:
October 12, 2006 - 08:55:04 AM »
keep playing and adjusting as stated above,, taping the edges is a VERY good idea. You will get it to fit better, unless your hinges are worn out.
Look for slop at the rivet points on the hinges, if ANYTHING is sloppy, the hinge needs rebuilt.
«
Last Edit: October 12, 2006 - 08:58:02 AM by WANG
»
Logged
Hurry,, Duane the tub,,I'm Dwouning....
426 pentastar
Jr. Member
Posts: 175
Re: hood alignment issues
«
Reply #6 on:
October 14, 2006 - 08:32:27 AM »
If you are using new hood wedges on the top of the fenders try to remove them to line it up.i had to remove the springs one time from the repop wedges in order for the hood to sit right.
Logged
Print
Pages: [
1
]
« previous
next »
Cuda-Challenger.com
»
Chryco's Tech Shop
»
The Body Shop
(Moderator:
Chryco Psycho
) »
hood alignment issues