u joint c clip

News:

  • Home
  • Help
  • Chat
  • Login
  • Register

    • « previous next »
    Pages: [1]

    Author Topic: u joint c clip  (Read 2187 times)

    Offline shadango

    • Resident
    • *****
    • Posts: 3920
    u joint c clip
    « on: May 02, 2009 - 02:50:44 AM »
    Ok, here's a real newbie question......   :screwy:

    The c-clips that are used to hold the caps in the u-joints ----  do new ones come with u-joints when ya buy em?

    If not, how hard are they to get?

    I pressed the old u joints out of the driveshaft I just bought and found that the one cap was missing its clip.

    Also, I pressed out the old joints but am worried that pressing the new ones in could be more difficult to do without damaging the new ones.....any tricks?  I am using the old vice-and-a-couple-of-sockets method....lol

    Thanks all....
    Logged


    Offline Chryco Psycho

    • Administrator
    • C-C.com Guru
    • *****
    • Posts: 36620
    • 70 Challenger R/T SE 70 tube Chassis Cuda now sold
    Re: u joint c clip
    « Reply #1 on: May 02, 2009 - 03:34:52 AM »
    yes the joints come supplied with new clips
     I still use the vice & sockets
    Logged

    Challenger - You`ll wish You Hadn`t

    Offline Changin Gears

    • Sr. Member
    • ****
    • Posts: 1011
    Re: u joint c clip
    « Reply #2 on: May 02, 2009 - 06:49:19 AM »
    If you do try to scrounge up a clip make sure it is the same thickness as the others in the new joint.  Different manufactures have different clips.

    I used my press once to install u-joints, wasn’t worth the effort.  Using the vice/sockets/hammer method ever since.
    Logged


    The goal never changes - Stop the 60' timer with your back tires

    Offline heminut

    • Resident
    • *****
    • Posts: 2023
    • owner of the poor man's Hemi Cuda
    Re: u joint c clip
    « Reply #3 on: May 02, 2009 - 09:57:50 AM »
    I still use the vise and sockets method too. Since you haven't put the u-joint in yet, take it back to the store you got it from and tell them it was short a clip. Chances are good they'll swap it for another one or give you a clip. Another option is to reuse one of the clips from the old u-joint if it's in good shape.
    Logged
    1970 5.7 Hemi Cuda

    Offline Bullitt-

    • Permanent Resident
    • *******
    • Posts: 12167
    • Better Things To Come Member Since 2/16/06
    Re: u joint c clip
    « Reply #4 on: May 02, 2009 - 10:15:23 AM »
    My good ole local Ace Hardware store (boy do I miss it), had a huge hardware section with a selection of C-clips.... My cousin lost a clip for his Jeep 4WD front axle & they had it.
    Logged
    Wade  73 Rallye 340..'77 Millennium Falcon...13 R/T Classic   Huntsville, AL
    Screwed by Photobucket!

    Offline shadango

    • Resident
    • *****
    • Posts: 3920
    Re: u joint c clip
    « Reply #5 on: May 02, 2009 - 02:53:47 PM »
    hey folks

    the sitiation was that I had lost an original clip, but hadnt yet bought the new u joints.......

    i ended up at Napa and they pressed in the new ones for me...they came with clips.

    A little miffed, though......though they installed two of the same part numbers, (super duty greasable 256 I think), one had the zerk-style of lube fitting in the middle of thejoint and the other has a "needlepoint tip" style, on the end......they didnt have two of the same.....and even if they had they didnt realize it till they were installed.

    So i had to buy an adaptor for my grease gun.....also means that this will be the odd zerk on the whole car.... :swear:

    I think NAPA is slipping.....used to be top nothc parts etc,..,.,.last time I bought new brake rotors for acar, they had the exact same part numbers but different rotors...........

    Anyways, the ujoints ar done and I just need to paint the shaft and then hook her up....ofcourse I need the tranny rebuilt for that...LOL

    Talk about the cart before the horse....
    Logged

    Offline Chryco Psycho

    • Administrator
    • C-C.com Guru
    • *****
    • Posts: 36620
    • 70 Challenger R/T SE 70 tube Chassis Cuda now sold
    Re: u joint c clip
    « Reply #6 on: May 02, 2009 - 11:37:42 PM »
    just change the grease nipple for a normal one
    Logged

    Challenger - You`ll wish You Hadn`t

    Offline shadango

    • Resident
    • *****
    • Posts: 3920
    Re: u joint c clip
    « Reply #7 on: May 03, 2009 - 01:12:14 AM »
    We went thru their rack of nipples...(hey that sounds kinky).......all the standard nipples were too large .......

    I guess that for as often as I will need to lube the thing it will be fine....it was just an annoying situation.....I dropped the shaft off for almost 3 hours......when I came back for it , it STILL wasnt done.....the guy told me that I hadnt told him which end matched up with the tranny yoke......but I had told the other guy I dropped it off with....LOL

    Like I said, no real harm.....just annoying.   :violin:
    Logged
    Pages: [1]
    « previous next »