Author Topic: How far back for H-pipe?  (Read 5058 times)

Offline GoodysGotaCuda

  • Sr. Resident
  • ******
  • Posts: 5392
Re: How far back for H-pipe?
« Reply #15 on: May 12, 2008 - 07:04:20 PM »
Every engine will have different exhaust temperatures due to it's build and so the ideal location for the balance pipe will vary.
The correct place for the H crossover can be determined (oldschool backyard method ;))by marking a crayon line along the pipe,start the engine and get up to temp and the point where the crayon melts to is the ideal location for the crossover pipe.
Of course by necessity things like trannys in the way can over ride the best location. ??? 

I thought that old school method was for header extensions only, not for full exhaust? I also thought it was to be checked after a hard run or 1/4 mile pass. Given that i would think the crayon would melt within a foot or so of the header collector, hardly any room in most cars to stick it there.  :wave:
Build Page: Goody's 'Cuda Build Page
1976 Dodge Warlock
1972 Barracuda - 5.7 Hemi + T56 Magnum

Wheel & Tire Specs:Link




Offline Chryco Psycho

  • Administrator
  • C-C.com Guru
  • *****
  • Posts: 36620
  • 70 Challenger R/T SE 70 tube Chassis Cuda now sold
Re: How far back for H-pipe?
« Reply #16 on: May 13, 2008 - 12:37:46 AM »
 :iagree:
 I know that is used for header extensions , never for an H pipe

Challenger - You`ll wish You Hadn`t

Offline IMNCARN82

  • Resident
  • *****
  • Posts: 3547
  • LeDZeP
Re: How far back for H-pipe?
« Reply #17 on: May 18, 2008 - 05:26:23 PM »
I'd try and put it back far enough to get the tranny out without dropping the exhaust. Mine was too close for comfort.And then I had to alter it for the 5 speed. 1 " can make it or break it. :dunno:   
'73 340 5 speed,RMS,BAER,... "Supercuda" (O[   ]||||[   ]O)  
'69 Dodge Charger 383,Auto                  (OiiiiiiiiiiIiiiiiiiiiiO)
13' Challenger R/T BlacktoP  6spd. (OO________OO)
71' Demon
75' Duster
87' Conquest TSI
56' Plaza
Boulder CO
Robert    "cuda bob"

Offline mikerallye

  • Jr. Member
  • **
  • Posts: 321
Re: How far back for H-pipe?
« Reply #18 on: June 10, 2008 - 04:02:43 PM »
What does the "H" pipe do?  :clueless: :clueless:

Offline Changin Gears

  • Sr. Member
  • ****
  • Posts: 1011
Re: How far back for H-pipe?
« Reply #19 on: June 10, 2008 - 04:51:40 PM »
An H-pipe (or X-pipe) allows each exhaust pulse to travel through both mufflers thereby reduceing back pressure.  This is why you can run say 3" pipes up to the H then reduce down to 2.5" after without adding restriction.  Its alot easier to run 2.5" tailpipes than 3".


The goal never changes - Stop the 60' timer with your back tires

Offline MEK-Dangerfield

  • C-C.com Expert
  • ********
  • Posts: 20946
  • I don't get NO respect! Member since 1/25/2002
Re: How far back for H-pipe?
« Reply #20 on: June 10, 2008 - 05:14:09 PM »
The "H" pipe makes it sound cool too.   :grinyes:

Mike

1970 Challenger - SOLD
2016 SXT+.  1 of 524 SXT+'s in Plumb-crazy for 2016.

Offline 422STROKER

  • Sr. Resident
  • ******
  • Posts: 5386
  • Member Since 6/3/06
Re: How far back for H-pipe?
« Reply #21 on: June 10, 2008 - 05:55:31 PM »
I ended up having a muffler shop weld up the whole thging and cut an H-pipe in as well.  Sounds nasty now with the 40 series muffs.  Resonance isn't tooo bad.LOL  Just have to find the sweet spot while cruising.

Tom

They cut the H-pipe far enough back to drop the trans through it. :2cents:
Tom
12.77 @ 108.87 15" Street Drag radial tires 3.23 gear

Offline johannes

  • Jr. Member
  • **
  • Posts: 281
Re: How far back for H-pipe?
« Reply #22 on: September 18, 2012 - 09:01:10 PM »
As long as the pressure can crossover bfore the muffler you will be fine


Fellas.
I just spent some extra time TRYING to capture the difference before and after H-pipe installation.
Yes I admit my camara skills leaves a lot to be desired, and my audio equipment even more so...
But it is the weather that sadens me the most

Did I jet my point across..... A "smoother tone to the ear" after H-pipe ?
Should I cut some of the footage out ?
Ohh well,...here goes, for your ears only... feedback welcome.
This video will be removed, and perhaps replaced by a better one?


Offline 422STROKER

  • Sr. Resident
  • ******
  • Posts: 5386
  • Member Since 6/3/06
Re: How far back for H-pipe?
« Reply #23 on: September 22, 2012 - 01:51:11 AM »
Nice video johannes.  Car is quieter on the road than I'd expect.

Tom
Tom
12.77 @ 108.87 15" Street Drag radial tires 3.23 gear