GenIII Hemi Tuning/Stand alone capabilities~ Need Help, everyone inside

[loganscuda]

I can get PCMs here locally they run about $75  If you let me know which ones you need to get files out of I will get it them to you.  year and model and trans setup

[diyhemi.com]

Yellowfin- I sent you a PM at FABO. Should I resend it here?

Yes, send it to me here. I haven't been in fabo in a while.

Also all files are welcomed. If you have a spare ECM that you could send me. I can scan and save the files then send the ECM back to you.

At this point, there is no need to go out of your way to buy ecms. I think we will more than fine just letting them trickle in.


Sent from my iPhone using Tapatalk

[diyhemi.com]

Testing is in full swing!


I mocked up my bench tuning interface to integrate the NGC3 connectivity, so far so good. Now I just need to neaten up the wire by eliminating barrel connectors and looming everything up.
Several files are stored in my database thus far, with a few more being done tonight. I am anxious to see how much we can push the envelope with the factory Chrysler NGC3 ECM's

[diyhemi.com]

I can get PCMs here locally they run about $75  If you let me know which ones you need to get files out of I will get it them to you.  year and model and trans setup

Would you happen to have any ECM's with manual transmission files? These are of particular interest, although not necessary to perform GENIII Hemi swaps.

I am also interested in any SRT8 base files, because that would help me develop a system for using truck ECM's on 6.1 and 6.4 GENIII swaps

[diyhemi.com]

Flashed the ECM tonight, with the help of HP Tuners. Fingers crossed


Sent from my iPhone using Tapatalk

[roadrunninMark]

  keep up the good work, YellowFin!

[diyhemi.com]

Thanks, roadrunninMark!

I have created a website with all of this information on it. It's very simple and easy to navigate. diyhemi.com

So far I have ECM pin outs, swap parts lists, descriptors and a step by step harness modification.

I will continue to add content until its release, later this month.

In the future I hope to ad tune files, tech videos, pictures of hemi swaps done by people that used the site, and information on my 1970 Gran Coupe build for motivation.


Sent from my iPhone using Tapatalk

[diyhemi.com]

A work in progress, with much more data to publish...

But diyhemi.com is now online.

I will update this thread as information is added.

Thank you for your time and patience!


Sent from my iPhone using Tapatalk

[soundcontrol]

Nice site! Checking it out now.

[diyhemi.com]

Website updated with OEM service manuals, base tune files and more. Be sure to hover over buttons in the navigation bar to access the sub-pages and get to additional content.

[roadrunninMark]

Checking it out too!

[diyhemi.com]

Would an admin be opposed to splitting this topic or making it a sticky? I think it could be a great tool for us all to reference. Videos will be published following the step by step wiring modifications additions.

Let's make Gen III Hemi swaps popular!

[diyhemi.com]

The LX section has been updated with a step by step instruction on converting an LX harness for stand alone purposes.

Be Aware that it is a ROUGH draft and needs pictures/revisions to be more user friendly. I will also be making a video to show how easy it can be. Approximate cost to perform this harness modification is $30. And that is NOT a typo...

Bare with me fellas, we will get there! For future questions or communications, email me at blake@diyhemi.com

Thanks!

[GreenFish]

Not sure if you saw this....

https://www.diyautotune.com/support/tech/install/chrysler-dodge/megasquirt-your-hemi/

[diyhemi.com]

I didn't see it, but it's a bit different than what we are doing on our website


Sent from my iPhone using Tapatalk