Where to find connector ?

[tomsa]

Hi
Where can I buy the connector sockets (correct term?? ) for the wire harness to ignition and turnsignal switches ?
I mean on the car side.
I have no wiring left in the car and would like to use the connectors on the switches and not cutting them if possible

[tomsa]

No ideas ?

[roadman5312]

Picture of what you need ?    Connectors from steering column ?  Little more info please. 

                                                                                         

[tomsa]

Picture of what you need ?    Connectors from steering column ?  Little more info please. 

                                                                                         

for the wire harness to ignition and turnsignal switches

those who sits in the harness in the car,the other one are attached when you buy a new ignition switch and turns signal switch

[tomsa]

the connector that should be attached at the red arrow

[72rtchallenger]

might be hard to find but I have seen some later 70 model vans with a plug that may work like on some 78 maybe up to 85 as this one on ebay http://www.ebay.com/itm/Dodge-Truck-Van-1972-85-New-Turn-Signal-Switch-TS111-/361348876767?hash=item54221249df&vxp=mtr  shows one but I am not positive , you would need to find one for a comparison ,,this one is on ebay http://www.ebay.com/itm/1970-71-72-73-74-NOS-MoPar-T-S-SWITCH-Cuda-Dart-Charger-Road-Runner-Challenger-/110293812740?hash=item19ae060604&vxp=mtr  but pricey . this one is for a dodge charger http://www.ebay.com/itm/Mopar-71-72-73-74-Charger-Turn-Signal-Switch-NEW-/400922137169?hash=item5d58d25251&vxp=mtr  but I am unsure about fit ,,
According to jegs Mopar Performance#312-04293102
Turn Signal Switch Assembly
1970-76 A-Body/B-Body/E-Body this will work http://www.jegs.com/i/Mopar+Performance/312/04293102/10002/-1?CAWELAID=1710733951&CAGPSPN=pla&catargetid=230006180000850347&cadevice=c&gclid=CISt34j4kscCFQeBaQodJnYIcg

I havent seen just the plug your looking for

Did find this one cheap for an a-body dart http://www.ebay.com/itm/Turn-Signal-Switch-without-Tilt-Column-for-73-79-Dodge-Plymouth-Chrysler-/231575326647?fits=Model%3ADart&hash=item35eaf70fb7&vxp=mtr

[tomsa]

To find the turn signal switch and the ignition switch is not a problem
I looking for the connectors that are in the wire harness that these 2 connects to .
Must be me english that's so bad that I can't explain this :-(

[roadman5312]

To find the turn signal switch and the ignition switch is not a problem
I looking for the connectors that are in the wire harness that these 2 connects to .
Must be me english that's so bad that I can't explain this :-(

              Called pigtails. Don't know anybody that makes them. Would have to be cut off and old harness.

[Got JOB]

Do you want just the white connector with the wires cut off?

[tomsa]

Ok
Easier to cut of the one on switch side and buy some weather proof connector or something like that
They are often small
Thanks

[tomsa]

Do you want just the white connector with the wires cut off?

Was looking for the connectors at the car side of the wire harness but I guess it's easier to change both sides to an other type of connectors

[Got JOB]

I think I have an old harness, I will look and see. If I do I can send it to you or just cut the wires off and send the plug.

[tomsa]

I think I have an old harness, I will look and see. If I do I can send it to you or just cut the wires off and send the plug.

A small problem that I live in Sweden maybe

[Got JOB]

I have an ignition switch with an 8 wire connector. Its yours if you want it. Give me a postal code and I can see about mailing.
Ricky

[tomsa]

I have an ignition switch with an 8 wire connector. Its yours if you want it. Give me a postal code and I can see about mailing.
Ricky

Don't need the connector on the switch side