WANTED: Dash parts

[anlauto]

Alan, I have the two outside speaker covers. I don't suppose you would have a RH lower dash trim you would like to trade? If not let me know what you think these are worth if you want them and they are yours.

Sorry I don't have any trim pieces extra.
I would pay $140 USD for your speakers (as shown in your pictures)  if you included postage to my CDN address.

[Sinatra]

Correct me if I'm wrong, but those are '71-up speaker grilles.  The '70 Challenger grilles have J/L and J/R cast into the back of them, as well as different casting numbers.  In '71 both cars used the '70 Barracuda castings.

I think I I have a non-AC Rallye heater bezel around here.  Is '72 the same?  It came from a Barracuda.

[Lbs]

These grilles are from a 73 cuda.........and they are on the way to the post office this morning. So Alan if they are not correct let me know as soon as you can.


Sent from my iPad using Tapatalk

[anlauto]

As far as the speaker grills, I'm aware of the different casting numbers for 70 Challenger etc....but don't understand what the difference could be ? the dash pads are all the same in that area...

[Lbs]

I'm heading to the post office


Sent from my iPad using Tapatalk

[1 Wild R/T]

As far as the speaker grills, I'm aware of the different casting numbers for 70 Challenger etc....but don't understand what the difference could be ? the dash pads are all the same in that area...

Reproduction pads are, an original 70 Challenger pad is not..... 

[anlauto]

Reproduction pads are, an original 70 Challenger pad is not.....

Do you know what the differences in those areas are ? I've tried to find pictures comparing the different speaker grills, with no luck. No one seems to know what's different ?

[1 Wild R/T]

Do you know what the differences in those areas are ? I've tried to find pictures comparing the different speaker grills, with no luck. No one seems to know what's different ?

The 70 Challenger pad it more deeply sculptured  so the grill has a greater curvature... If you use a 70 Challenger grill on the more common pas the front & rear edge don't pull down tightly where as the center is buried into the pad... 

Use a 71 grill on a 70 Challenger pad & the area near the screws wants to float while the front & rear edges are digging into the pad...

[anlauto]

I think I I have a non-AC Rallye heater bezel around here.  Is '72 the same?  It came from a Barracuda.

Just realized I don't need this part because the Vintage Air kit I'm going to buy supplies one modified for their system.

[crash340]

Sorry I don't ship.....

 

yeah, I might have some of those things but im too lazy to go look as I dont ship either

[70chall440]

yeah, I might have some of those things but im too lazy to go look as I dont ship either

That's funny because I have heard you complain greatly because some US guy didn't want to ship to Auzzie land... just saying...

[anlauto]

It's just an inside joke...Everybody is busting my chaps because I listed parts for sale here, but insisted on local pick up only....The cost of shipping parts out of Canada is crazy.....I try to give people good deals, but when it cost $37 to ship a $20 part....it's quite ridiculous 

I just had one guy that wanted me to mail him one nut $0.25 and one stud $0.25....To Quebec. Forget that it would take an hour out of my day to remove the stud, buy a padded envelope, pack the parts up and get them to the Post Office...all to make $0.50 cents   I'm not that nice

[70chall440]

No worries, I was just bust his backside... its all good. 

[roadman5312]

It's just an inside joke...Everybody is busting my chaps because I listed parts for sale here, but insisted on local pick up only....The cost of shipping parts out of Canada is crazy.....I try to give people good deals, but when it cost $37 to ship a $20 part....it's quite ridiculous 

I just had one guy that wanted me to mail him one nut $0.25 and one stud $0.25....To Quebec. Forget that it would take an hour out of my day to remove the stud, buy a padded envelope, pack the parts up and get them to the Post Office...all to make $0.50 cents   I'm not that nice

                       If the guy is a member have him PM me, if I have what he needs I'll send it to him. Or he can e mail me @  roadman5312@aol.com. Post office is just down the street.       

[AARTA340]

Shipping over the border, doesn't matter which direction, has gone up considerably from what it used to be. I don't mind paying the the extra if the parts warrant it, but I have to agree, for a nickle part, no way.