Something weird going on

News:

  • Home
  • Help
  • Chat
  • Login
  • Register

    • « previous next »
    Pages: 1 ... 6 7 [8] 9 10 ... 21

    Author Topic: Something weird going on  (Read 46625 times)

    Offline cudabob496

    • Sr. Resident
    • ******
    • Posts: 8024
    Re: Something weird going on
    « Reply #105 on: November 14, 2016 - 05:03:14 PM »
    Big update! Still won't run!!! suspect primary side bowl float and seat. Although
    I inspected closely, and the valve seat was a couple years old. And did not detect any
    leak in the float. But Holley thought vacuum leak or too much fuel, from perhaps a leaking
    power valve. But power valves and metering blocks are new.
    Will report back, after changing primary float and seat.
    Logged
    72 Cuda, owned 25 years. 496, with ported Stage VI heads, .625 in solid roller, 254/258 at .050, 3500 stall, 3.91 rear. 850 Holley DP, Reverse manual valve body.

    1999 Trans Am, LS1, heads, cam, headers, stall, etc! Love to surprise the rice rockets with this one. They seem so confident, then it's "what the heck just happened?"

    2011 Kawasaki Z1000


    Offline cudabob496

    • Sr. Resident
    • ******
    • Posts: 8024
    Re: Something weird going on
    « Reply #106 on: November 14, 2016 - 07:17:41 PM »
    to make sure, changed 180 rotation on dist, but just got a big backfire,
    so that ain't it. Hope it didn't blow a power valve.

    Primary bowl had no gas indication in sight viewing hole, but when unscrewed
    lock bolt on needle/seat assembly, got pressurized gas out.  Replaced float needle seat assembly, ran
    a tad better, but will now replace float with a new Holley plastic one.
    « Last Edit: November 14, 2016 - 07:19:14 PM by cudabob496 »
    Logged
    72 Cuda, owned 25 years. 496, with ported Stage VI heads, .625 in solid roller, 254/258 at .050, 3500 stall, 3.91 rear. 850 Holley DP, Reverse manual valve body.

    1999 Trans Am, LS1, heads, cam, headers, stall, etc! Love to surprise the rice rockets with this one. They seem so confident, then it's "what the heck just happened?"

    2011 Kawasaki Z1000

    Offline cudabob496

    • Sr. Resident
    • ******
    • Posts: 8024
    Re: Something weird going on
    « Reply #107 on: November 15, 2016 - 01:52:20 AM »
    I'm sure my problem is here somewhere.
    How tell if PCV valve is working correctly?

    https://www.holley.com/blog/post/troubleshooting_engine_idles_rough__stall_/
    Logged
    72 Cuda, owned 25 years. 496, with ported Stage VI heads, .625 in solid roller, 254/258 at .050, 3500 stall, 3.91 rear. 850 Holley DP, Reverse manual valve body.

    1999 Trans Am, LS1, heads, cam, headers, stall, etc! Love to surprise the rice rockets with this one. They seem so confident, then it's "what the heck just happened?"

    2011 Kawasaki Z1000

    Offline cudabob496

    • Sr. Resident
    • ******
    • Posts: 8024
    Re: Something weird going on
    « Reply #108 on: November 15, 2016 - 04:53:57 PM »
    well, new float on primary side,
    but car still will not run.
    Time to start over I guess.
    What I've done so far:

    New intake gasket
    New plugs
    New Dist mag pickup
    New carb metering blocks
    New coil

    Still thinking prob is in carb somewhere.

    guess I'll check under valve cover on driver side as well.
    « Last Edit: November 15, 2016 - 04:56:08 PM by cudabob496 »
    Logged
    72 Cuda, owned 25 years. 496, with ported Stage VI heads, .625 in solid roller, 254/258 at .050, 3500 stall, 3.91 rear. 850 Holley DP, Reverse manual valve body.

    1999 Trans Am, LS1, heads, cam, headers, stall, etc! Love to surprise the rice rockets with this one. They seem so confident, then it's "what the heck just happened?"

    2011 Kawasaki Z1000

    Offline HP_Cuda

    • Hit the skinny little pedal on the right!
    • Sr. Resident
    • ******
    • Posts: 5268
    • Mopar or No Car!
    Re: Something weird going on
    « Reply #109 on: November 15, 2016 - 05:02:09 PM »

    Take a known good carb and slap it on there.

     :horse:
    Logged
    1970 Cuda Clone 440 4 speed - sublime green
    1970 Cuda 383 4 speed - yellow - SOLD

    Offline timbbuc2

    • Jr. Member
    • **
    • Posts: 221
    Re: Something weird going on
    « Reply #110 on: November 15, 2016 - 05:18:57 PM »
     I just went back and read your complete thread, does not make any sense, but have you checked your fuel pump , low RPMS may not produce enough fuel pressure.  :2cents:
    Tim
    Logged

    Offline cudabob496

    • Sr. Resident
    • ******
    • Posts: 8024
    Re: Something weird going on
    « Reply #111 on: November 15, 2016 - 05:33:20 PM »
    Quote from: HP_Cuda on November 15, 2016 - 05:02:09 PM
    Take a known good carb and slap it on there.

     :horse:

    yes, would have if I owned one.
    But even if I didn't, seems a person could dissasemble a card and determine what
    was wrong with it, which I have done. Tempted to send carb to Holley for an inspection.
    But I have had it completely apart.
    Logged
    72 Cuda, owned 25 years. 496, with ported Stage VI heads, .625 in solid roller, 254/258 at .050, 3500 stall, 3.91 rear. 850 Holley DP, Reverse manual valve body.

    1999 Trans Am, LS1, heads, cam, headers, stall, etc! Love to surprise the rice rockets with this one. They seem so confident, then it's "what the heck just happened?"

    2011 Kawasaki Z1000

    Offline cudabob496

    • Sr. Resident
    • ******
    • Posts: 8024
    Re: Something weird going on
    « Reply #112 on: November 15, 2016 - 05:37:40 PM »
    If I put #1 cylinder at TDC on the power stroke, where
    should my distributor rotor be pointing. Think I have about
    15 degrees initial timing set.
    Logged
    72 Cuda, owned 25 years. 496, with ported Stage VI heads, .625 in solid roller, 254/258 at .050, 3500 stall, 3.91 rear. 850 Holley DP, Reverse manual valve body.

    1999 Trans Am, LS1, heads, cam, headers, stall, etc! Love to surprise the rice rockets with this one. They seem so confident, then it's "what the heck just happened?"

    2011 Kawasaki Z1000

    Offline cudabob496

    • Sr. Resident
    • ******
    • Posts: 8024
    Re: Something weird going on
    « Reply #113 on: November 16, 2016 - 03:14:43 AM »
    Quote from: timbbuc2 on November 15, 2016 - 05:18:57 PM
    I just went back and read your complete thread, does not make any sense, but have you checked your fuel pump , low RPMS may not produce enough fuel pressure.  :2cents:
    Tim

    yes, thanks, at least 5 psi on gauge inside car.
    Logged
    72 Cuda, owned 25 years. 496, with ported Stage VI heads, .625 in solid roller, 254/258 at .050, 3500 stall, 3.91 rear. 850 Holley DP, Reverse manual valve body.

    1999 Trans Am, LS1, heads, cam, headers, stall, etc! Love to surprise the rice rockets with this one. They seem so confident, then it's "what the heck just happened?"

    2011 Kawasaki Z1000

    Offline cudabob496

    • Sr. Resident
    • ******
    • Posts: 8024
    Re: Something weird going on
    « Reply #114 on: November 16, 2016 - 03:16:24 AM »
    Driver side valve train looks good.

    withdrew a gas sample, looks and smells good.

    gonna check timing by rotating engine to TDC and looking at markings on dampner.
    Logged
    72 Cuda, owned 25 years. 496, with ported Stage VI heads, .625 in solid roller, 254/258 at .050, 3500 stall, 3.91 rear. 850 Holley DP, Reverse manual valve body.

    1999 Trans Am, LS1, heads, cam, headers, stall, etc! Love to surprise the rice rockets with this one. They seem so confident, then it's "what the heck just happened?"

    2011 Kawasaki Z1000

    Offline cudabob496

    • Sr. Resident
    • ******
    • Posts: 8024
    Re: Something weird going on
    « Reply #115 on: November 16, 2016 - 01:27:37 PM »

    Here is what Holley is saying:

    Robert,
    Man you are having my luck. Its perplexing. As I read through your article you and everybody are asking the right questions. Now anytime you make changes to the carburetor does it make any difference on how it runs? Better or worse? Just a little bit? If its not the engine it would be the idle circit. All things you guys have already figured out. My guts still say transfer slots are uncovered. Normally the car will run solely off the idle fuel will exit below the throttle plate. At idle the transfer slot will be above the throttle plates and not emit gas or suck air. The pressure in the venture will equalize the psi in the slot. When the throttle is opened even slightly air rushes bast the transfer slot and pulls fuel out and into the engine. If your throttle plates are adjusted inproperly and allowing fuel to be pulled out of the transfer slots and air to enter the engine this would cause the problems you are having. It isa acceptable to have them uncovered a tiny bit. If the slot looks like a dot its ok. If you can visually see it’s a slot its to far.
    Best bet to save you some time and headache see if you can find a carburetor that you know is good. Swap it on and see what happens. At least then you can narrow it down A little. Did you ever do a compression test. A bad valve has caused this headache for me once before. Check the slots. Try a different carburetor. You have nearly replaced everything that maybe worn it sounds on the carburetor. So its either adjustment of engine.
                                                                                                                    Josh
    Logged
    72 Cuda, owned 25 years. 496, with ported Stage VI heads, .625 in solid roller, 254/258 at .050, 3500 stall, 3.91 rear. 850 Holley DP, Reverse manual valve body.

    1999 Trans Am, LS1, heads, cam, headers, stall, etc! Love to surprise the rice rockets with this one. They seem so confident, then it's "what the heck just happened?"

    2011 Kawasaki Z1000

    Offline cudabob496

    • Sr. Resident
    • ******
    • Posts: 8024
    Re: Something weird going on
    « Reply #116 on: November 17, 2016 - 06:34:07 PM »
    got new floatst in, and new needle/valve assemblies
    Carb is set up good I believe.
    Got gas in bowls, fuel pressure, still will not run.
    Now it is not firing. So since I got fuel and air,
    gonna start over again on the electrical system.
    Maybe something ain't grounded right.
    Logged
    72 Cuda, owned 25 years. 496, with ported Stage VI heads, .625 in solid roller, 254/258 at .050, 3500 stall, 3.91 rear. 850 Holley DP, Reverse manual valve body.

    1999 Trans Am, LS1, heads, cam, headers, stall, etc! Love to surprise the rice rockets with this one. They seem so confident, then it's "what the heck just happened?"

    2011 Kawasaki Z1000

    Offline cudabob496

    • Sr. Resident
    • ******
    • Posts: 8024
    Re: Something weird going on
    « Reply #117 on: November 17, 2016 - 10:28:46 PM »
    son of a gun, I have been doing all this replacing and rebuiding,
    and I just started electrical troubleshooting again, and my brand new MSD blaster
    coil I bought a month ago is testing bad!

    So, a bad coil is what I determined early on, and I replaced it, and
    turns out the new one was bad, and I did all kinds of other replacing
    and rebuilding for nothing.

    Moral of story, when get a new coil, test it before using it.
    supposed to be positive to tower, .7 ohms, and neg to tower 4700 ohms.
    I'm getting 25 ohms and 1200 ohms
    Logged
    72 Cuda, owned 25 years. 496, with ported Stage VI heads, .625 in solid roller, 254/258 at .050, 3500 stall, 3.91 rear. 850 Holley DP, Reverse manual valve body.

    1999 Trans Am, LS1, heads, cam, headers, stall, etc! Love to surprise the rice rockets with this one. They seem so confident, then it's "what the heck just happened?"

    2011 Kawasaki Z1000

    Offline 734406pk

    • Andy
    • Sr. Member
    • ****
    • Posts: 1716
    Re: Something weird going on
    « Reply #118 on: November 17, 2016 - 11:46:27 PM »
    Quote from: cudabob496 on November 17, 2016 - 10:28:46 PM
    son of a gun, I have been doing all this replacing and rebuiding,
    and I just started electrical troubleshooting again, and my brand new MSD blaster
    coil I bought a month ago is testing bad!

    So, a bad coil is what I determined early on, and I replaced it, and
    turns out the new one was bad, and I did all kinds of other replacing
    and rebuilding for nothing.

    Moral of story, when get a new coil, test it before using it.
    supposed to be positive to tower, .7 ohms, and neg to tower 4700 ohms.


    I'm getting 25 ohms and 1200 ohms

     How is the spark output? Its unlikely that both the  primary and secondary sides of the same coil have shorted out in one month... Do you agree?
    Logged
    1973 Challenger 440 6 pack auto 3.91 rear
    2012 Dodge Ram 3500 dually 6.7 Cummins Fleece EFI Live
    1973 Challenger 318 2bbl auto 2.73 rear 22.5 mpg RIP
    1970 Challenger TA 340 4bbl auto-Sold and sad
    1999 Dodge Ram 3500 dually 5.9 Cummins Fleece tuned VGT-sold
    1995 Kawasaki ZX1100E & still alive

    Offline cudabob496

    • Sr. Resident
    • ******
    • Posts: 8024
    Re: Something weird going on
    « Reply #119 on: November 18, 2016 - 12:41:25 AM »
    Quote from: 734406pk on November 17, 2016 - 11:46:27 PM
    How is the spark output? Its unlikely that both the  primary and secondary sides of the same coil have shorted out in one month... Do you agree?

    I did the resistence test, which it failed, but first used the MSD test procedure to check out the ignition system.
    and it also pointed to the coil. Was getting no spark at my spark tester.
    « Last Edit: November 18, 2016 - 12:47:55 AM by cudabob496 »
    Logged
    72 Cuda, owned 25 years. 496, with ported Stage VI heads, .625 in solid roller, 254/258 at .050, 3500 stall, 3.91 rear. 850 Holley DP, Reverse manual valve body.

    1999 Trans Am, LS1, heads, cam, headers, stall, etc! Love to surprise the rice rockets with this one. They seem so confident, then it's "what the heck just happened?"

    2011 Kawasaki Z1000
    Pages: 1 ... 6 7 [8] 9 10 ... 21
    « previous next »