Rust Bullet or POR 15 inside the frames

[Topcat]

Anyone know of a way to get a good amount of spray of either POR or Rust Bullet inside the frames? I would like to get the back half frames a good coat inside.

My car is on a rotisserie.

[Chlngrcrzy]

  Great idea. I will be watching this one too. Hope somebody has some info.

[farmboy70]

For enclosed areas you can get a rocker shutz gun and modify a tube similar to a under coating kit. These have a spray end attached to spray a fan. Just slide it in a access hole and pull back out as you spray.
 A good auto body suppy store should have a inexpensive under coat spray kit. You could also fabricate a end to do this also.
Dave

[R/T hedkace]

For enclosed areas you can get a rocker shutz gun and modify a tube similar to a under coating kit. These have a spray end attached to spray a fan. Just slide it in a access hole and pull back out as you spray.
 A good auto body suppy store should have a inexpensive under coat spray kit. You could also fabricate a end to do this also.
Dave

 That's pretty good to know Dave. Never thought of anything like that 

 Another good thing that I found works just as good is to Completely remove your trunk floor, and any other panel that may be in your way, ( even if they're not rusty, take em out anyways. It will save you a ton of time in the long run  ..........J/K
 But it was pretty convenient for me 



 Actually, I'd just listen to Dave if I was you 

[Topcat]

For enclosed areas you can get a rocker shutz gun and modify a tube similar to a under coating kit. These have a spray end attached to spray a fan. Just slide it in a access hole and pull back out as you spray.
 A good auto body suppy store should have a inexpensive under coat spray kit. You could also fabricate a end to do this also.
Dave

Thanks Dave for the heads up. I'll pay them a visit on Monday then to get what I need. I already did the trunk rails while the floor was out.

[Topcat]

Ahaaa!!! This must be the critter I need.

https://www.autobodytoolmart.com/p-14347-4648-3m-rust-fighter-i-application-wand-08998.aspx

[Topcat]

And use this too?

Ever try this stuff or should I stick with using the POR?

https://www.autobodytoolmart.com/p-14348-4150-3m-rust-fighter-i-08891.aspx

[farmboy70]

Ahaaa!!! This must be the critter I need.

https://www.autobodytoolmart.com/p-14347-4648-3m-rust-fighter-i-application-wand-08998.aspx

Yep thats the wand I was talking about , the gun is listed on that page also.
Dave

[farmboy70]

And use this too?

Ever try this stuff or should I stick with using the POR?

https://www.autobodytoolmart.com/p-14348-4150-3m-rust-fighter-i-08891.aspx

That product is for replacing the rust protection on a repaired panel. I would use the POR or Rustbullit to kill the rust that is already there myself.
Dave

[Topcat]

Great I'm buying the wand, gun, and Rust Bullet right away, 

[farmboy70]

 

[dougs bs23]

you can pick up a shutz gun for around 20 dollars at eastwood,  also there rust encapsulator and to undercoat everything else spray on bedliner,  I used there gator gaurd II A little messy but with some prep masking and in a "tent "worked very well.


http://www.eastwoodco.com/

[Topcat]

Hemiken just helped me out today with one I bought on e bag. It had the wand and the gun for 15 bucks. Kenny sent him the MO to the seller for me and then I paid him. Thanks again Kenny. 

[hemiken]

  More than happy to help out a fellow C-C.Com brother.

[RUSTY Cuda]

I used the eastwood one with por 15, messy but effective!
I just used a plain old piece of 3/8" tubing to extend the rod to get all the way into the rockers & long frame rails. Rich.