Author Topic: Axle bearings  (Read 11935 times)

Offline RDF

  • Sr. Member
  • ****
  • Posts: 1840
  • The pain that greets me is the stick that beats me
Axle bearings
« on: April 20, 2008 - 09:30:14 PM »
I'm about to change my rear axles with a used set I bought from a member here.  He said the bearings were good (and they weren't the Green bearings) but he recommended changing them since I have the axles out already.  I bought a set of bearings from the parts store (not Green) and my question is, are they pressed on?  If so, where would I take the axles to have the bearings changed out?  Is this something I can do myself without major tools and whatnot?

 :dunno:
Bob

1973 'Cuda

If we never drown we'll never know how well it tastes....So tell me how it tastes and I'll know just how well you drowned.

My build:
http://www.cuda-challenger.com/cc/index.php?topic=45749.0




Offline Chryco Psycho

  • Administrator
  • C-C.com Guru
  • *****
  • Posts: 36620
  • 70 Challenger R/T SE 70 tube Chassis Cuda now sold
Re: Axle bearings
« Reply #1 on: April 20, 2008 - 09:43:29 PM »
you need to cut the retainer ring off to remove the brg , the have the retainer ring back on after the brg is in place

Challenger - You`ll wish You Hadn`t

Offline Moparal

  • Permanent Resident
  • *******
  • Posts: 13085
Re: Axle bearings
« Reply #2 on: April 20, 2008 - 10:05:27 PM »
 :iagree:

I use a 2" pipe about 4 ft long to slide down the axle to put the retainer back on. That was in the 1980's :bigsmile:  I have a press now :2thumbs:

Offline RDF

  • Sr. Member
  • ****
  • Posts: 1840
  • The pain that greets me is the stick that beats me
Re: Axle bearings
« Reply #3 on: April 21, 2008 - 08:44:45 AM »
So it wounds like I will need 2 new retainer clips (1 for each side) if I have to cut the old ones off, correct?
Bob

1973 'Cuda

If we never drown we'll never know how well it tastes....So tell me how it tastes and I'll know just how well you drowned.

My build:
http://www.cuda-challenger.com/cc/index.php?topic=45749.0

Offline hemiken

  • Sr. Resident
  • ******
  • Posts: 8785
  • Hemi-fied Mopar in Australia
Re: Axle bearings
« Reply #4 on: April 21, 2008 - 08:51:42 AM »
Yes RDF you are correct buddy.  :2thumbs:
1970 Barracuda   (O^--^===|===^--^O)
1971 Barracuda   (O O {]{]{]|[}[}[} O O)
1970 Challenger  (O O [======R/T=] O O)
1971 Challenger  (O O ===== ===== O O)
I pay homage to the best Mopars ever built.

Offline RDF

  • Sr. Member
  • ****
  • Posts: 1840
  • The pain that greets me is the stick that beats me
Re: Axle bearings
« Reply #5 on: April 21, 2008 - 12:26:54 PM »
Is this the retainer clip you are referring to?  I'm having issues finding one, if anyone knows where I can get one (or has some), please let me know.
« Last Edit: April 21, 2008 - 12:46:52 PM by RDF »
Bob

1973 'Cuda

If we never drown we'll never know how well it tastes....So tell me how it tastes and I'll know just how well you drowned.

My build:
http://www.cuda-challenger.com/cc/index.php?topic=45749.0

Offline GoodysGotaCuda

  • Sr. Resident
  • ******
  • Posts: 5392
Re: Axle bearings
« Reply #6 on: April 21, 2008 - 01:01:24 PM »
If you figure you need a press, i got one at work Bob.
Build Page: Goody's 'Cuda Build Page
1976 Dodge Warlock
1972 Barracuda - 5.7 Hemi + T56 Magnum

Wheel & Tire Specs:Link

Offline Moparal

  • Permanent Resident
  • *******
  • Posts: 13085
Re: Axle bearings
« Reply #7 on: April 21, 2008 - 01:02:56 PM »
When your at the parts house, get the axle bearing kit. It has everything in it...or it used to :2thumbs:

Offline Chryco Psycho

  • Administrator
  • C-C.com Guru
  • *****
  • Posts: 36620
  • 70 Challenger R/T SE 70 tube Chassis Cuda now sold
Re: Axle bearings
« Reply #8 on: April 21, 2008 - 01:22:00 PM »
it is a retainer ring not a clip , it is shown in the exploded window as serviced in package #

Challenger - You`ll wish You Hadn`t

Offline RDF

  • Sr. Member
  • ****
  • Posts: 1840
  • The pain that greets me is the stick that beats me
Re: Axle bearings
« Reply #9 on: April 21, 2008 - 02:32:53 PM »
If you figure you need a press, i got one at work Bob.

Thanks Mike....I just picked up the brake tool, a brake tubing wrench and some brake fluid (DOT 4).

When your at the parts house, get the axle bearing kit. It has everything in it...or it used to :2thumbs:
I didn't by the package at any store, I bough the oil seals (4) and bearings (2) at a Dodge dealership that still sells old parts and the foam gaskets I bought off ebay.  I called autozone, napa, and advance auto parts but no one seems to have that clip..... :clueless:
Bob

1973 'Cuda

If we never drown we'll never know how well it tastes....So tell me how it tastes and I'll know just how well you drowned.

My build:
http://www.cuda-challenger.com/cc/index.php?topic=45749.0

Offline Mt.St.BigBlock

  • Jr. Member
  • **
  • Posts: 198
Re: Axle bearings
« Reply #10 on: April 21, 2008 - 03:26:57 PM »
Hi, the retaining collar came with the new bearings I bought from Carquest about two
years ago.   Jeff
71 cuda 383 3spd manual gy9

Offline ShelbyDogg

  • Sr. Resident
  • ******
  • Posts: 5007
Re: Axle bearings
« Reply #11 on: April 21, 2008 - 10:54:22 PM »
The bearing retainer still comes with the bearings. You should change the seals too.   Here are my pics:

http://www.cuda-challenger.com/cc/index.php?topic=35471.0

Rob
Rob

3 E-bodies, Megasquirt-1v3.0, Edelbrock Pro-Flo-1, Holley C950, FAST EZ-EFI; say no to carbs...yes to throttle bodies

My Pace Car restoration thread:
http://www.cuda-challenger.com/cc/index.php?topic=44869.0


Offline ksierens

  • Sr. Member
  • ****
  • Posts: 1408
    • 70 Challenger Resurrection
Re: Axle bearings
« Reply #12 on: April 22, 2008 - 08:07:03 AM »
Do the adjusters and retainers need to be replaced also?
1970 Triple Black Challenger R/T  440 Six Pack - 4 Speed - 3.55 Dana
Kurt - SE Michigan

Offline RDF

  • Sr. Member
  • ****
  • Posts: 1840
  • The pain that greets me is the stick that beats me
Re: Axle bearings
« Reply #13 on: April 22, 2008 - 09:20:07 AM »
ok, I'm in a bit of a pickle here.....Neither Advance auto, auto zone or carquest have the bearing kit or just the retainer by itself.  I tried looking real quick online (while at work) and the only ebay item I found is for the Green bearings which Rob mentions to keep away from, which I will.  Can anyone think of another place I can find this clip?  This is killing me here....I've got the bearings, race, and 2 oil seals for each axle but now I can't find the one part I really need.... :swear:
Bob

1973 'Cuda

If we never drown we'll never know how well it tastes....So tell me how it tastes and I'll know just how well you drowned.

My build:
http://www.cuda-challenger.com/cc/index.php?topic=45749.0

Offline hemiken

  • Sr. Resident
  • ******
  • Posts: 8785
  • Hemi-fied Mopar in Australia
Re: Axle bearings
« Reply #14 on: April 22, 2008 - 09:26:14 AM »
In the exploded view the piece you want is called a "collar" measure the axle is the collar could be interchangable with other makes.  My suggestion would be to contact a differential specialist and ask them where to get the collars from. :2thumbs: They may even have these collars in stock. :wave:
1970 Barracuda   (O^--^===|===^--^O)
1971 Barracuda   (O O {]{]{]|[}[}[} O O)
1970 Challenger  (O O [======R/T=] O O)
1971 Challenger  (O O ===== ===== O O)
I pay homage to the best Mopars ever built.