Reference pictures

[Topcat]

Pic of ink stamping on a NOS 1971 Cuda header upper valence.
Located on driver's side.

http://img695.imageshack.us/img695/126/valence71.jpg

[NoMope Greg]

Pic of ink stamping on a NOS 1971 Cuda header upper valence.
Located on driver's side.

[roy282]

Thought I would share this great web link  Many good  References found here  http://www.iccahome.org/

[Topcat]

71 Hemi Cuda Shaker cable grommet hole location.

Same for 70' except 71' had 2 cables coming out instead of one.
71's were a manual operated choke making the second cable.

[RUSTY Cuda]

This one gets asked for a lot, 1973 e-brake cables

[Topcat]

The 4 speed reverse light location on the dash.

[Topcat]

Posted earlier in another post, these belong here.

[usraptr]

Below is a picture of how the emergency brake cable that goes to the passenger rear wheel, on a '70 'Cuda, is secured to the back of the rear seat housing/body.  If it's been a few years since you removed the original, like me, you might have forgotten where this tab is attached, I did.  I searched pics high and low on numerous sites and couldn't find where this was attached.  The picture in the instructions and motor manual are vague to say the least.  It took my mechanic son 30 seconds, naturally, to notice the raised/threaded  bracket.  I kept looking rearward in the area of the axle instead of turning around and looking at the body.    

[Topcat]

Idle solenoid p/n's


3514520 Early (AVS)
3549318 Late (AVS)
DR1114421
70 440 4737S,4739S, 4741S, 4740S
Hex head with cap, no integral bracket

3514892 (AVS)
DR1114442
70 340 4936S, 4937S
Round head, no integral bracket

3438303 (AVS)
DR1114442 or DR1114447 (Have reports of both)
70 440 4738S
71 440 4968S
Hex head with cap, no integral bracket

3438777 (Holley)
DR1114441
71 383 4667A, 4734A, 4668A, 4735A, 6191A, 6193A
Hex head with cap, no integral bracket, but includes wiring harness

2875975 (Holley, AFB)
DR1114429
70 440+6 4375A, 4734A, 4376A, 4144A
70 340+6 4791A, 4792A
70 426 4745S, 4746S
71 426 4969S, 4970S
Round head with integral bracket

3438338 (Holley)
DR1114443
71 440+6 4669A, 4670A
Hex head with cap, and integral bracket

3412059 (Holley)
DR1114420
69 440+6
Hex head with cap, and integral bracket

3438333 (Same as 2875975) (TQ)
DR1114429
71 340 4972S, 4973S
Round head with integral bracket

[gtx6970]

Dec 1969 SBD - 1970 Challenger 340 - LA plant 3.23 open rear axle

[gtx6970]

1970 Cuda tail panel location print

[usraptr]

Recently finished re-doing the rear drum brakes on my '70 'Cuda.  Here are some pictures of the the spring connections, hardware, etc. in case you forgot  how yours went back together.  The red stripe on the brake drum was applied with a paint brush as per factory.  Since everything I have read said it was applied on the assembly line, I was not real careful about "staying within the lines" so to speak.  I took numerous pictures before I took the brakes apart.  The new brakes/springs/hardware are attached exactly as they were before dis-assembly.  Of course there is no guarantee that the last person who worked on the brakes put them back correctly, if they had even been worked since being installed at the factory.

[TinCuda]

1970 Cuda tail panel location print

Do you have a print for the 'Cuda and the "by Plymouth" layout?


.,

[Topcat]

4 speed Center Console bracket location.





]

[Topcat]

Correct "Shaggy" insulation on my car when it was taken apart.

Nobody offers it as a reproduction to my knowledge.