News:

  • Home
  • Help
  • Chat
  • Login
  • Register

    • « previous next »
    Pages: 1 ... 3 4 [5] 6

    Author Topic: Reference pictures  (Read 56806 times)

    Offline cwestra

    • Sr. Member
    • ****
    • Posts: 1120
    Re: Reference pictures
    « Reply #60 on: July 02, 2012 - 07:20:18 AM »
    Eyebrow Spoiler AAR fender hole locations (passenger side fender shown):

    Horizontal dimensions are 2-1/2" and 6-3/16".
    Vertical dimensions are 2-1/2" and 4-1/8".
    Remaining hole on the valance can be roughly determined from these.
    Logged
    Corey - in Northern Indiana


    Offline Topcat

    • C-C.com Expert
    • ********
    • Posts: 15376
    • Member since 9/16/04
    Re: Reference pictures
    « Reply #61 on: September 30, 2012 - 07:25:40 PM »
    Master Cylinder Bore Diameter Chart.
    This is important if you are going back to OEM disc brakes.




    Those that have posted here on this thread in the past, please review your attachment and re-post it using an uploader such as Imageshack so it won't be discarded.
    Logged
    Mike, Fremont, CA.

    Offline Topcat

    • C-C.com Expert
    • ********
    • Posts: 15376
    • Member since 9/16/04
    Re: Reference pictures
    « Reply #62 on: September 30, 2012 - 07:31:28 PM »
    4 speed Brake pedal/Clutch assembly drawing:



    Logged
    Mike, Fremont, CA.

    Offline Topcat

    • C-C.com Expert
    • ********
    • Posts: 15376
    • Member since 9/16/04
    Re: Reference pictures
    « Reply #63 on: September 30, 2012 - 07:38:12 PM »
    Side Passenger Door Glass assembly:



    Logged
    Mike, Fremont, CA.

    Offline Topcat

    • C-C.com Expert
    • ********
    • Posts: 15376
    • Member since 9/16/04
    Re: Reference pictures
    « Reply #64 on: September 30, 2012 - 07:52:34 PM »
    Non A/C Heater Cable Layout. Notice the picture of the special "J" Hook on the lower right that is required to correctly mount the heater box on the Passenger side.



    Logged
    Mike, Fremont, CA.

    Offline Topcat

    • C-C.com Expert
    • ********
    • Posts: 15376
    • Member since 9/16/04
    Re: Reference pictures
    « Reply #65 on: September 30, 2012 - 07:56:45 PM »
    Rear Window De-fogger.



    Logged
    Mike, Fremont, CA.

    Offline Topcat

    • C-C.com Expert
    • ********
    • Posts: 15376
    • Member since 9/16/04
    Re: Reference pictures
    « Reply #66 on: September 30, 2012 - 08:02:51 PM »
    Organosol Paint Code:



    Logged
    Mike, Fremont, CA.

    Offline burdar

    • Sr. Resident
    • ******
    • Posts: 5925
    Re: Reference pictures
    « Reply #67 on: November 25, 2012 - 08:26:54 PM »
    I was asked to post this here.  It shows the areas that I had to trim on my Ultimate Rides dash pad in order to get it to fit.  You may or may not have to trim these areas.  Every pad seems to be a little different.

     







    Original center speaker opening....no vinyl down inside rectangular opening.
     

    Had to trim vinyl/foam out of this area so the speaker cover would fit.  Screw holes were also off and had to redrill them.


    This is a bad pic but it shows the right hand side of the dash where it lines up with the dash frame.(the frame is on the top...the pad is on the bottom)  The red lines should be lined up.  There is a lot of excess foam where the blue arrow is pointing.  By trimming the foam away on the inside, the pad will move to the left and line up closer to the dash frame. 
    Logged

    Offline Topcat

    • C-C.com Expert
    • ********
    • Posts: 15376
    • Member since 9/16/04
    Re: Reference pictures
    « Reply #68 on: November 25, 2012 - 09:44:23 PM »
    Speedometer cable clips.
    Very hard to find the plastic part. Try junk yards if you're in need of one. Not reproduced.

     http://www.cuda-challenger.com/cc/index.php?topic=88966.msg881986#msg881986

    Logged
    Mike, Fremont, CA.

    Offline Topcat

    • C-C.com Expert
    • ********
    • Posts: 15376
    • Member since 9/16/04
    Re: Reference pictures
    « Reply #69 on: November 27, 2012 - 10:33:56 PM »
    Speedometer cable routing & Plstic clip.


    Logged
    Mike, Fremont, CA.

    Offline Topcat

    • C-C.com Expert
    • ********
    • Posts: 15376
    • Member since 9/16/04
    Re: Reference pictures
    « Reply #70 on: November 30, 2012 - 09:46:15 PM »
    B & E bodies used different length brake booster push rods for the Hemi Bendix brake booster.
    The E body used the longer length as shown in the picture.






    Logged
    Mike, Fremont, CA.

    Offline elmoska

    • Jr. Member
    • **
    • Posts: 155
    Re: Reference pictures
    « Reply #71 on: December 24, 2012 - 09:10:56 AM »
    Quote from: Topcat on September 30, 2012 - 07:56:45 PM
    Rear Window De-fogger.





    do you have more picture of this casing before you put it in
    Logged
    1974 challenger on its way..

    Offline anlauto

    • Permanent Resident
    • *******
    • Posts: 12328
    • I'm Alan G...I'm a Mopar Addict
      • Alan Gallant Automotive Restoration
    Re: Reference pictures
    « Reply #72 on: December 24, 2012 - 09:16:10 AM »
    Quote from: elmoska on December 24, 2012 - 09:10:56 AM

    do you have more picture of this casing before you put it in

    That is a picture of the "WORLD FAMOUS BARRELCUDA"  I don't have any more pictures of the unit, but they do make a reproduction of it.
    Logged
    I've taught you everything you know.....but I haven't taught you everything I know !
    www.alangallantautomotiverestoration.com

    Offline elmoska

    • Jr. Member
    • **
    • Posts: 155
    Re: Reference pictures
    « Reply #73 on: December 24, 2012 - 10:39:09 AM »
    look like thats all i have .. and the blower seems to have the same bolt patern as the speaker...

    Logged
    1974 challenger on its way..

    Offline Suulan1

    • Jr. Member
    • **
    • Posts: 41
    Re: Reference pictures
    « Reply #74 on: March 05, 2013 - 08:00:07 AM »
    Hi!
    I wonder if anyone could take some measurements or rather a picture of the T/A 340 six pack fender decal size AND location
    I have to make those myself since the engine in my car is a 392 4barrel
    Logged
    Pages: 1 ... 3 4 [5] 6
    « previous next »