News:

  • Home
  • Help
  • Chat
  • Login
  • Register

    • « previous next »
    Pages: [1]

    Author Topic: moving rear springs in?  (Read 1090 times)

    Offline JoeGrapes

    • Full Member
    • ***
    • Posts: 508
    moving rear springs in?
    « on: April 15, 2012 - 03:01:08 PM »
    I'm putting bigger wheels and tires on but the space between the tire and the spring is not as much as I want. I noticed that front spring spacing (48")is 2" narrower than the rear spacing (50"). Is there any reason I can't move the rear in 3/4" on a side with out moving the front location? I may need to put a small shim in the outboard bolts of the front hanger but that will be small. I also realize the pin in the spring will be off location to the axle saddle but I can fix that. Maybe make up an offset lowering block. 
    Logged


    Offline ChallengerHK

    • Sr. Resident
    • ******
    • Posts: 7338
    • I'm working on it - No, really
    Re: moving rear springs in?
    « Reply #1 on: April 15, 2012 - 03:27:31 PM »
    There are kits sold to do just that.
    Logged


    "She'll make point five past light speed. She may not look like much, but she's got it where it counts, and I've made a lot of special modifications myself."

    - Han Solo, Star Wars

    Advice Thread - Taking Pictures Of Cars

    Offline JoeGrapes

    • Full Member
    • ***
    • Posts: 508
    Re: moving rear springs in?
    « Reply #2 on: April 15, 2012 - 03:41:00 PM »
    Yes I know. I was under the impression that when you move the springs in you had to move both the from and rear mounting points. I just want to move the rear mounting point. 
    Logged

    Offline 72cudamaan

    • Resident
    • *****
    • Posts: 3248
    Re: moving rear springs in?
    « Reply #3 on: April 15, 2012 - 04:18:29 PM »
    But your pivot point is the front spring perch. That means if you move the rear
    inward 3/4 inch, at midpoint you only gain 3/8 inch. If you want to obtain 3/4 inch
    then you will have to go with the relocation kit. That would put a lot less stress
    on the front bushing and bolt as well.
    Logged
    If I cant fix it, it's broke
     
    Andy  (phukker whither)

    Offline JoeGrapes

    • Full Member
    • ***
    • Posts: 508
    Re: moving rear springs in?
    « Reply #4 on: April 15, 2012 - 05:07:29 PM »
    yes you are right about moving only about 3/8 at the axle saddle. The tire will come into contact with the spring father back toward the shackle so the distance will be greater but it will be less than 3/4". I'll probably end up moving both the front and rear mounts. It was a thought anyway.
    Logged

    Offline Chryco Psycho

    • Administrator
    • C-C.com Guru
    • *****
    • Posts: 36620
    • 70 Challenger R/T SE 70 tube Chassis Cuda now sold
    Re: moving rear springs in?
    « Reply #5 on: April 19, 2012 - 12:26:23 PM »
    Doctor Diff has offset rear shackles but it will not move it very far .
    Logged

    Challenger - You`ll wish You Hadn`t

    Offline HP2

    • Resident
    • *****
    • Posts: 4478
    Re: moving rear springs in?
    « Reply #6 on: April 19, 2012 - 05:32:02 PM »
    Quote from: 72cudamaan on April 15, 2012 - 04:18:29 PM
    That means if you move the rear inward 3/4 inch, at midpoint you only gain 3/8 inch. If you want to obtain 3/4 inch then you will have to go with the relocation kit. That would put a lot less stress
    on the front bushing and bolt as well.

    True, but E body springs are splayed wider at the back. So while you may only move 3/8" at the axle centerline (which is in not the spring centerpoint, BTW), your gains in the rear segment where the tire will actually hit will be more like 5/8" to 11/16" depending on how tall your tire is.

    You'll still need to alter the axle hosuing seat location with this method, so if your going to that trouble, you might as well go the full 3/4" route.
    Logged
    Pages: [1]
    « previous next »