Author Topic: 727 to A518 swap � a novice guide (Read 282317 times)

RCCDrew · « **Reply #15 on:** May 10, 2012 - 04:36:51 AM »

Awesome thread. I too want to do this as 4.10s make my cuda unhappy on the freeway.
A couple questions. Has anyone used a shift cable to make the slap stik work instead of the factory linkage? Also, what happens if you shift the Od switch in first or second?

360FISH · « **Reply #16 on:** May 11, 2012 - 01:23:53 AM »

Quote from: tactransman on May 09, 2012 - 10:38:44 PM

Great thread. <snip>

Thanks Terry. Coming from you, I really appreciate it. Your input helped me get motivated to set my sights on this swap.

The 3 pin tranny is easy to find and the pressure switch setup you mention looks simple enough to tackle... it loooks like a keeper!

Alan

360FISH · « **Reply #17 on:** May 11, 2012 - 01:30:02 AM »

Quote from: RCCDrew on May 10, 2012 - 04:36:51 AM

Awesome thread. I too want to do this as 4.10s make my cuda unhappy on the freeway.
A couple questions. Has anyone used a shift cable to make the slap stik work instead of the factory linkage? Also, what happens if you shift the Od switch in first or second?

Hey Drew... I know people have switched to cable shifters but I don't know if anyone has documented it.... Maybe the "Grand Daddy" thread listed in refrences on page one will have someone who mentioned it... they might be willing to describe it.

The OD won't engage until it's in third gear if the switch is on early... it will engage right away though and you won't get all of 3rd. I've forgotten about being in OD coming off the FWY, came to a stop and the car was okay.

360FISH · « **Reply #18 on:** May 11, 2012 - 01:53:09 AM »

Quote from: _Russ_ on May 10, 2012 - 04:33:33 AM

Awesome thread mate. 32548 rep points!

Bookmarked.

Thanks Russ, can I cash those points in for a paint job?

Cheers!

ragtopdodge · « **Reply #19 on:** May 15, 2012 - 01:35:50 PM »

Quote from: ragtopchally on May 08, 2012 - 11:24:22 AM

I'm wondering what Rory would recommend for a converter.

I understand you want a stall speed a bit less than your cruise rpm?

In otherwords, say I have a 4.10 rear, 26" tire, and a .75OD reduction going 65MPH. My RPM is roughly 2657 RPM. Does that mean I want a converter say at 2500 to avoid excessive slippage? Since I have a non-lockup converter, this is especially crucial???

?

the_engineers · « **Reply #20 on:** May 15, 2012 - 04:04:17 PM »

Quote from: ragtopchally on May 08, 2012 - 11:24:22 AM

I'm wondering what Rory would recommend for a converter.

I understand you want a stall speed a bit less than your cruise rpm?

In otherwords, say I have a 4.10 rear, 26" tire, and a .75OD reduction going 65MPH. My RPM is roughly 2657 RPM. Does that mean I want a converter say at 2500 to avoid excessive slippage? Since I have a non-lockup converter, this is especially crucial???

There was dicussion about this in another thread somewhere. IIRC, a 2500 rpm converter flashes to 2500; at 50% throttle, it would engage at roughly 1250 rpm, so you should be fine.

Fontana motorsports · « **Reply #21 on:** May 26, 2012 - 03:56:40 PM »

Just to let everyone know, we are working on this swap for the B/RB engines..will keep you guys up to date as we come to the final product.
Rory

scorpn · « **Reply #22 on:** June 18, 2012 - 02:26:46 AM »

Finally finished this swap this weekend.. That trans mount from Rory is a real beauty, I did have to drill a hole on the back side for my e-brake equalizer bar, other than that it is perfect. While I was at it I also installed new Hooker Super Comp headers and a total new exhaust system. I am running a 400hp Mopar crate 360 motor so had a heck of a time figuring out the torque converter required.. Finally figured out the Mopar Crate 360 is internally balanced, unlike a normal 360 that is externally balanced. Using a 2000 stall lock up converter with shift control from the governor port and a vacuum switch.. Runs super smooth on the highway and brought my rpm down to 2000 at 75mph. Over 5mpg improvement in fuel economy so far... I am using the same cable shifter and cable kick down system that I had on the 727, works good so far..
Just wanted to say Thank You for your excellent write up's. They are what gave me the courage to try this myself..

ragtopdodge · « **Reply #23 on:** June 18, 2012 - 12:10:11 PM »

Quote from: scorpn on June 18, 2012 - 02:26:46 AM

Finally finished this swap this weekend.. That trans mount from Rory is a real beauty, I did have to drill a hole on the back side for my e-brake equalizer bar, other than that it is perfect. While I was at it I also installed new Hooker Super Comp headers and a total new exhaust system. I am running a 400hp Mopar crate 360 motor so had a heck of a time figuring out the torque converter required.. Finally figured out the Mopar Crate 360 is internally balanced, unlike a normal 360 that is externally balanced. Using a 2000 stall lock up converter with shift control from the governor port and a vacuum switch.. Runs super smooth on the highway and brought my rpm down to 2000 at 75mph. Over 5mpg improvement in fuel economy so far... I am using the same cable shifter and cable kick down system that I had on the 727, works good so far..
Just wanted to say Thank You for your excellent write up's. They are what gave me the courage to try this myself..

Got any pics? Do you have a lockup or non-lockup 'verter?

scorpn · « **Reply #24 on:** June 19, 2012 - 01:06:51 AM »

Quote from: ragtopchally on June 18, 2012 - 12:10:11 PM

Got any pics? Do you have a lockup or non-lockup 'verter?

Camera card was corrupted.. Will try to get more pics when I put the header wrap on..
It is the Lock-up torque converter.

Chilly · « **Reply #25 on:** June 19, 2012 - 10:32:10 AM »

scorpn, what gear ratio and tire size you running. trying to figure what stall converter to use for sons car. I have lock-up style also. Chilly

scorpn · « **Reply #26 on:** June 19, 2012 - 02:50:42 PM »

Quote from: Chilly on June 19, 2012 - 10:32:10 AM

scorpn, what gear ratio and tire size you running. trying to figure what stall converter to use for sons car. I have lock-up style also. Chilly

Rear gear is a 323 and the tire size's are 245/40/18 front and 275/40/18 rear.. Speedometer is absolutely dead on with a 33 tooth yellow gear..

Aussie Challenger · « **Reply #27 on:** June 23, 2012 - 08:28:39 AM »

This is a great thread and it should be a sticky, I am looking at doing this to my Little Red Express Truck seems as it is an auto with 3.55 rear gears. I have been looking around the net and asking many who should know but not too many are willing to pass on this info, thanks.
I will be using the PATC setup for the OD & LU control but I do like the adjustable switch idea just in case the change points are a little off.

360FISH · « **Reply #28 on:** June 24, 2012 - 12:43:22 AM »

Quote from: scorpn on June 18, 2012 - 02:26:46 AM

Finally finished this swap this weekend.. That trans mount from Rory is a real beauty, I did have to drill a hole on the back side for my e-brake equalizer bar, other than that it is perfect. While I was at it I also installed new Hooker Super Comp headers and a total new exhaust system. I am running a 400hp Mopar crate 360 motor so had a heck of a time figuring out the torque converter required.. Finally figured out the Mopar Crate 360 is internally balanced, unlike a normal 360 that is externally balanced. Using a 2000 stall lock up converter with shift control from the governor port and a vacuum switch.. Runs super smooth on the highway and brought my rpm down to 2000 at 75mph. Over 5mpg improvement in fuel economy so far... I am using the same cable shifter and cable kick down system that I had on the 727, works good so far..
Just wanted to say Thank You for your excellent write up's. They are what gave me the courage to try this myself..

That's soo cool Scorp! I'm glad it worked out and you're happy.
My 'Cuda is taking two trips this weekend and the OD is starting to pay me back in gas money.

Quote from: Aussie Challenger on June 23, 2012 - 08:28:39 AM

This is a great thread and it should be a sticky, I am looking at doing this to my Little Red Express Truck seems as it is an auto with 3.55 rear gears. I have been looking around the net and asking many who should know but not too many are willing to pass on this info, thanks.
I will be using the PATC setup for the OD & LU control but I do like the adjustable switch idea just in case the change points are a little off.

Thank you, I really want to see pictures of your conversion when you start it.

Enjoy!

Alan

rockymopar · « **Reply #29 on:** June 24, 2012 - 06:58:58 AM »

Aussie, A518s were factory options in 90-93 ram pickups. I think It is darn near a bolt in for your truck. A driveshaft, might be the only thing that would gave to be custom as shortbeds and stepsides were pretty much dead by then

Author Topic: 727 to A518 swap � a novice guide (Read 282317 times)

RCCDrew

727 to A518 swap � a novice guide

360FISH

Re: 727 to A518 swap � a novice guide

360FISH

Re: 727 to A518 swap � a novice guide

360FISH

Re: 727 to A518 swap � a novice guide

ragtopdodge

Re: 727 to A518 swap � a novice guide

the_engineers

Re: 727 to A518 swap � a novice guide

Fontana motorsports

Re: 727 to A518 swap � a novice guide

scorpn

Re: 727 to A518 swap � a novice guide

ragtopdodge

Re: 727 to A518 swap � a novice guide

scorpn

Re: 727 to A518 swap � a novice guide

Chilly

Re: 727 to A518 swap � a novice guide

scorpn

Re: 727 to A518 swap � a novice guide

Aussie Challenger

Re: 727 to A518 swap � a novice guide

360FISH

Re: 727 to A518 swap � a novice guide

rockymopar

Re: 727 to A518 swap � a novice guide