Author Topic: Get into EFI at Carlisle (Read 5141 times)

fastmanefi · « **on:** June 12, 2012 - 07:23:04 PM »

I'll be doing two sets of EFI seminars at Carlisle on Friday and Saturday July 6 -8. The sessions will be an introduction to EFI and then a "getting started". Come on down and ask all the questions you want!!!

In between, I will be available to tune, or touch up, any FAST EFI Mopar.

brads70 · « **Reply #1 on:** June 12, 2012 - 10:40:09 PM »

Sounds great see you there!

MEK-Dangerfield · « **Reply #2 on:** June 13, 2012 - 07:08:31 AM »

Where exactly will you be having your seminar on the fairgrounds?

fastmanefi · « **Reply #3 on:** June 13, 2012 - 01:08:45 PM »

Quote from: MEK-Dangerfield on June 13, 2012 - 07:08:31 AM

Where exactly will you be having your seminar on the fairgrounds?

Not sure yet. Ed (the manager) is deciding that today, but it would most likely be under a large tent so we have some breeze. I will be doing the same 2 seminars on Friday and Saturday.

brads70 · « **Reply #4 on:** June 13, 2012 - 04:18:12 PM »

I'm looking at the FAST controller to build a custom hidden ( somewhat) EFI set up with this STR-14 intake.

fastmanefi · « **Reply #5 on:** June 14, 2012 - 02:13:51 PM »

Quote from: brads70 on June 13, 2012 - 04:18:12 PM

I'm looking at the FAST controller to build a custom hidden ( somewhat) EFI set up with this STR-14 intake.

Very doable. Talk to me at Carlisle

joelson6 · « **Reply #6 on:** June 14, 2012 - 05:10:53 PM »

HEY, WHERE DID YOU GET THAT GASKET

i have STR14-4 intake i'd love to try but everyone says i have to use silicone to seal it up.

ya notice how those tops aren't interchangeable?

thedodgeboys · « **Reply #7 on:** June 14, 2012 - 05:32:17 PM »

Man I would use that new Holly Na$car throttal body on that manifold it would look sweet.

Fast man how much turning are you looking to do on a car? What's the charge?

brads70 · « **Reply #8 on:** June 14, 2012 - 10:55:46 PM »

Quote from: fastmanefi on June 14, 2012 - 02:13:51 PM

Very doable. Talk to me at Carlisle

Will do! Thanks!

Quote from: joelson6 on June 14, 2012 - 05:10:53 PM

HEY, WHERE DID YOU GET THAT GASKET

i have STR14-4 intake i'd love to try but everyone says i have to use silicone to seal it up.

ya notice how those tops aren't interchangeable?

The gasket came with the intake. It's junk though , hard as a rock and very brittle. I wouldn't use silicone on anything that see's fuel. It turns to jelly. Use Permatex gasket maker, better stuff!
The tops are interchangeable? On mine anyhow? Depends on what base you have.

fastmanefi · « **Reply #9 on:** June 15, 2012 - 10:15:24 AM »

Quote from: thedodgeboys on June 14, 2012 - 05:32:17 PM

Fastman how much turning are you looking to do on a car? What's the charge?

My tuning input and assistance is free assuming there is nothing wrong with the installation and the tune just needs to be "tweaked". I'll connect to your ECU, look at the program, and make suggestions and/or changes as required. But if we go on the road and do drivability adjustments then it's a function of how much time we spend at $100 per hour.

joelson6 · « **Reply #10 on:** June 15, 2012 - 10:58:21 PM »

Quote from: brads70 on June 14, 2012 - 10:55:46 PM

The gasket came with the intake. It's junk though , hard as a rock and very brittle. I wouldn't use silicone on anything that see's fuel. It turns to jelly. Use Permatex gasket maker, better stuff!
The tops are interchangeable? On mine anyhow? Depends on what base you have.

i had 2 STR intakes . a 6 pack and a 4bbl. the 6 pack top wouldn't fit on the 4 bbl bottom and the 4 bbl top wouldn't fit on the 6 pack bottom.
the bolt holes on the front and back of the intakes were different. the sides matched up though.

thanks for the permatex tip

thedodgeboys · « **Reply #11 on:** June 16, 2012 - 09:19:28 AM »

Quote from: fastmanefi on June 15, 2012 - 10:15:24 AM

My tuning input and assistance is free assuming there is nothing wrong with the installation and the tune just needs to be "tweaked". I'll connect to your ECU, look at the program, and make suggestions and/or changes as required. But if we go on the road and do drivability adjustments then it's a function of how much time we spend at $100 per hour.

Thanks for the info, I'm thinking it's time to switch over to the xfi from my AEM box sadly I made a poor choice 4 years ago, and thought MOPAR made a good choice in selecting this box. I like the new updates fast has made.

I'll get back to you.
Ss

brads70 · « **Reply #12 on:** June 16, 2012 - 09:31:14 AM »

Quote from: joelson6 on June 15, 2012 - 10:58:21 PM

i had 2 STR intakes . a 6 pack and a 4bbl. the 6 pack top wouldn't fit on the 4 bbl bottom and the 4 bbl top wouldn't fit on the 6 pack bottom.
the bolt holes on the front and back of the intakes were different. the sides matched up though.

thanks for the permatex tip

That's weird?

I just checked mine and both lids fit on the base? (6 pack and single 4 bbl lids)
Are you sure they are both STR-14 intakes ? One of them might be a STR-15? There is also a dual 4 bbl version called the STR-14-8 that the base and lid are different.
I started a post awhile back trying to learn what I could about them.
http://www.cuda-challenger.com/cc/index.php?topic=77905.0

joelson6 · « **Reply #13 on:** June 18, 2012 - 11:54:46 PM »

Quote from: brads70 on June 16, 2012 - 09:31:14 AM

That's weird? I just checked mine and both lids fit on the base? (6 pack and single 4 bbl lids)
Are you sure they are both STR-14 intakes ? One of them might be a STR-15? There is also a dual 4 bbl version called the STR-14-8 that the base and lid are different.
I started a post awhile back trying to learn what I could about them.
http://www.cuda-challenger.com/cc/index.php?topic=77905.0

oh, i'm positive. they both said STR14 on them. and the both fit on a 440. i still have pics of the six pack, but i sold that one.
gotta find them though, i think the pics are on my office computer. here's a pic of the 4bbl.

you know what, i'm looking at the lid for your six pack and mine was different. gotta find those pics............

ShelbyDogg · « **Reply #14 on:** June 28, 2012 - 08:31:38 AM »

Rich, I hope to see you there. I told my another user here "sprecks" (Jay Sprecker) about your site a couple of weeks ago at Monster Mopar Weekend in St. Louis. I found out that he just got his EZ-EFI from you yesterday. It'll be on his hemi-Challenger convertible soon! I'll be getting a couple of computers from you soon too, to convert my systems over to FAST.

Author Topic: Get into EFI at Carlisle (Read 5141 times)

fastmanefi

Get into EFI at Carlisle

brads70

Re: Get into EFI at Carlisle

MEK-Dangerfield

Re: Get into EFI at Carlisle

fastmanefi

Re: Get into EFI at Carlisle

brads70

Re: Get into EFI at Carlisle

fastmanefi

Re: Get into EFI at Carlisle

joelson6

Re: Get into EFI at Carlisle

thedodgeboys

Re: Get into EFI at Carlisle

brads70

Re: Get into EFI at Carlisle

fastmanefi

Re: Get into EFI at Carlisle

joelson6

Re: Get into EFI at Carlisle

thedodgeboys

Re: Get into EFI at Carlisle

brads70

Re: Get into EFI at Carlisle

joelson6

Re: Get into EFI at Carlisle

ShelbyDogg

Re: Get into EFI at Carlisle