Having trouble with TTI header install and 5.7 .... can anyone help?

News:

  • Home
  • Help
  • Chat
  • Login
  • Register

    • « previous next »
    Pages: [1]

    Author Topic: Having trouble with TTI header install and 5.7 .... can anyone help?  (Read 3604 times)

    Offline PlumCrazyChris

    • Jr. Member
    • **
    • Posts: 456
      • Mopar Muscle Cars of Austin
    Having trouble with TTI header install and 5.7 .... can anyone help?
    « on: November 03, 2012 - 04:29:39 PM »
    So far I've pulled the torsion bar on the driver side, loosened the power steering gearbox, and it still won't go in.   :banghead:

    I think I'll need to pull the motor to get those damn things on.   :pullinghair:

    anyone have any insight into this install?  Any help will be appreciated.
     :bigsmile:

    Thanks
    Chris
    Logged
    PlumCrazyChris
    Mopar Muscle Cars of Austin
    Round Rock Tx
    70 Challenger 5.7, A518, A/C
    70 Challenger 340 convertible (Gone to Sweden)
    68 Barracuda (sold it too)
    www.mopar.org


    Offline autodynamics

    • Jr. Member
    • **
    • Posts: 42
    Re: Having trouble with TTI header install and 5.7 .... can anyone help?
    « Reply #1 on: November 03, 2012 - 09:20:01 PM »
    When I did mine I believe I put one in pass side and the drivers i laid in when before I put the motor in
    Logged

    Offline thedodgeboys

    • Resident
    • *****
    • Posts: 3633
    • ''Normal’s Overrated''
      • THE DODGE BOYS
    Re: Having trouble with TTI header install and 5.7 .... can anyone help?
    « Reply #2 on: November 04, 2012 - 03:13:45 PM »
    Chris
    Have you tried to go up from the bottom?

    Also un bolting the motor mounts and lifting the motor up and over to one side could help  :dunno:

    I've always done them at the same time toe motor was installed.. Good luck.
    Logged
    Go Fast & Have Fun...
    70 6.1 HEMI 6-speed Drop Top...

    Offline PlumCrazyChris

    • Jr. Member
    • **
    • Posts: 456
      • Mopar Muscle Cars of Austin
    Re: Having trouble with TTI header install and 5.7 .... can anyone help?
    « Reply #3 on: November 05, 2012 - 01:51:56 PM »
    I needed to remove my trans cooling lines, and then with the gearbox loosened, I was able to finally slip it into position on the drivers side.  The passenger side went in easy, but its nearly impossible to access the bolts to tighten it up!   :eek2:   I got them in with my fingers, but I'll be damned if I can get a wrench in there to tighten them up....   I'll try to finish up tonight.

    Now I just need to get this thing wired up to the battery and fill the fluids.... 
    Logged
    PlumCrazyChris
    Mopar Muscle Cars of Austin
    Round Rock Tx
    70 Challenger 5.7, A518, A/C
    70 Challenger 340 convertible (Gone to Sweden)
    68 Barracuda (sold it too)
    www.mopar.org

    Offline 67vertman

    • Sr. Resident
    • ******
    • Posts: 5125
    • Member since 9-23-2005
    Re: Having trouble with TTI header install and 5.7 .... can anyone help?
    « Reply #4 on: November 05, 2012 - 08:38:36 PM »
    Yep, there are a couple of bolts that are a b1tch to get to.  I use a modified wrench to tighten them.  Take an old wrench and heat it up and bend it so you can get it in there.
    Logged



    Ron - Born and raised in Southern California

    I got the 1970 Cuda, but still need the hot blonde to ride shotgun!

    First car -1969 Road Runner 383 4sp

    Current ride - 1970 Barracuda 440-6 4 sp Dana 60  (4:10)

    Offline PlumCrazyChris

    • Jr. Member
    • **
    • Posts: 456
      • Mopar Muscle Cars of Austin
    Re: Having trouble with TTI header install and 5.7 .... can anyone help?
    « Reply #5 on: November 07, 2012 - 06:34:45 PM »
    Man I hope I don't have to resort to that, but anything to make it easier. 

    Thanks for the tip.
    Logged
    PlumCrazyChris
    Mopar Muscle Cars of Austin
    Round Rock Tx
    70 Challenger 5.7, A518, A/C
    70 Challenger 340 convertible (Gone to Sweden)
    68 Barracuda (sold it too)
    www.mopar.org

    Offline Rolling_Thunder

    • Jr. Member
    • **
    • Posts: 194
    • only 2 things get my attention, gas and perfume
    Re: Having trouble with TTI header install and 5.7 .... can anyone help?
    « Reply #6 on: December 12, 2012 - 09:06:37 PM »
    Did the headers on my 6.1 three damn times - some of the bolts are a complete nightmare...   lots of cussing and yelling those days.
    Logged
    2013 Dodge Challenger R/T - 5.7L / 6-speed

    1973 Dodge Challenger Rallye - 340 / Auto

    1968 Dodge Charger - 6.1L / 6-speed

    1964 Dodge Polara - 440 8-71 / 4-speed

    Offline PlumCrazyChris

    • Jr. Member
    • **
    • Posts: 456
      • Mopar Muscle Cars of Austin
    Re: Having trouble with TTI header install and 5.7 .... can anyone help?
    « Reply #7 on: January 14, 2013 - 06:14:37 PM »
    I had to heat up and bend a wrench, it worked pretty easy after that. 

    Thanks for the Tip  67vertman!!
    Logged
    PlumCrazyChris
    Mopar Muscle Cars of Austin
    Round Rock Tx
    70 Challenger 5.7, A518, A/C
    70 Challenger 340 convertible (Gone to Sweden)
    68 Barracuda (sold it too)
    www.mopar.org

    Offline Haddixj

    • Full Member
    • ***
    • Posts: 641
    Re: Having trouble with TTI header install and 5.7 .... can anyone help?
    « Reply #8 on: January 14, 2013 - 06:41:45 PM »
    Can you post a pic of the wrench? I have a 6.1l going in my 70 and plan on running the factory set charger manifolds as I am told they will fit. If not I will resort to building a set
    Logged

    Offline PlumCrazyChris

    • Jr. Member
    • **
    • Posts: 456
      • Mopar Muscle Cars of Austin
    Re: Having trouble with TTI header install and 5.7 .... can anyone help?
    « Reply #9 on: January 22, 2013 - 04:00:06 PM »
    I just took an old 7/16" or 3/8" open end wrench, (I don't remember the exact size, just check it on one of the bolt heads), and stuck the box end in the vice and turned on the torch.  I bent the wrench about 2" down from the open end.    I guess that means I bent it almost in half, since the whole thing is only about 4.5" long....  well, that's what she said anyway... :biggrin:

    I'll try to post a pic if i can find that wrench.
    Logged
    PlumCrazyChris
    Mopar Muscle Cars of Austin
    Round Rock Tx
    70 Challenger 5.7, A518, A/C
    70 Challenger 340 convertible (Gone to Sweden)
    68 Barracuda (sold it too)
    www.mopar.org

    Offline 67vertman

    • Sr. Resident
    • ******
    • Posts: 5125
    • Member since 9-23-2005
    Re: Having trouble with TTI header install and 5.7 .... can anyone help?
    « Reply #10 on: January 22, 2013 - 09:39:53 PM »
    Quote from: PlumCrazyChris on January 14, 2013 - 06:14:37 PM
    I had to heat up and bend a wrench, it worked pretty easy after that. 

    Thanks for the Tip  67vertman!!

    Yep! the old modified wrench tip, works every time.  In a few years you will pick up that wrench and wonder why its bent.  :smilielol:
    Logged



    Ron - Born and raised in Southern California

    I got the 1970 Cuda, but still need the hot blonde to ride shotgun!

    First car -1969 Road Runner 383 4sp

    Current ride - 1970 Barracuda 440-6 4 sp Dana 60  (4:10)
    Pages: [1]
    « previous next »