** 72cudamaan AKA .... Andy needs our HELP! **

[diyhemi.com]

I also have small block torsion bars

[HP_Cuda]

I have an oil windage tray that I get add, as well I too have a set of small block torsion bars painted and ready to go.

[72cudamaan]

Andy can we assume you have the big sector shaft steering box? also, 72 stock size spindles?
I have the 73-74 stock spindles here with the pin caliper bracket for the bigger rotors?
I have the Lokar downshift cable ( just the cable and arm on the tranny) and a 727?
I have a 750 Holley(3310) vac secondary is nothing better comes up?
Brands new in the box PS pump (from local jobber, it looks a little different but works?)
I have a nice drive shaft but it's for a Challenger?  We could get it shortened if nothing else turns up?
I have the brand new in the box 3/8 fuel sending unit with 1/4" return ( new from Roseville) Cuda same as Challenger?

I have the old Idler and pitman arms I replaced them when I got my car with the fast ratio ones?
Are you all set for a tranny, rear end, leaf springs etc..? As mentioned I have them too! Leaf springs have hangers and shackles on them too.
 

I have the large sector shaft steering box and 73-up spindles
I may have found an A518 trans. I'll check if the lokar cable will work
I have a set of leaf springs, but no idea if they are any good.
The fuel sender appears to be the same. Do you have a part # Brad?
I'm not sure on a driveshaft yet, depends on which tranny I end up using?
I'm not fussy about a ps pump as long as it works

[72cudamaan]

I have one spare windshield but it has a birds eye chip near the center, may be repairable.

I have an extra moog idle arm, new in box that is yours now

I also have a driveshaft that is yours.

Let me wait on the windshield. I'm afraid of the crack growing.
  on the idler arm
Have to wait on the driveshaft (depends on what trans)
Using a b/b motor so I don't know if the torsion bars will work or not?
Thank you very much. 

[brads70]

I have the large sector shaft steering box and 73-up spindles
I may have found an A518 trans. I'll check if the lokar cable will work
I have a set of leaf springs, but no idea if they are any good.
The fuel sender appears to be the same. Do you have a part # Brad?
I'm not sure on a driveshaft yet, depends on which tranny I end up using?
I'm not fussy about a ps pump as long as it works

Sending unit says U112C on the box? 3/8" out with 1/4" return

[CUDA JAS]

I have a set of used smallblock torsion bars...no clips or boots.

I think I have a set of tie rod adjuster sleves around here some where, but not sure.

Yours if you need them.

Jason

[jimynick]

Just saw this and words kinda fail me. Where IS Andy? I've a Challenger, so lots of my spare stuff won't work, but if it's possible to send things, then I'll see what I can do. Andy, what's your address- you can PM me if you choose? Ian

[brads70]

Just saw this and words kinda fail me. Where IS Andy? I've a Challenger, so lots of my spare stuff won't work, but if it's possible to send things, then I'll see what I can do. Andy, what's your address- you can PM me if you choose? Ian

He is in Ann Arbor MI, I most likely will be driving down with a load of parts , maybe I could take what ever your donating down at the same time?   

[Chryco Psycho]

I have a lot of these parts in my Sea container back in AB , I doubt I can get to them though & shipping would be tough , I have a number of starters ,alts, ecu , dist , oil pans , timing covers , 50 pullies ,spare headers , big block T bars & leafs , just not sure how to get them .

[4Cruizn]

He is in Ann Arbor MI, I most likely will be driving down with a load of parts , maybe I could take what ever your donating down at the same time?   

Yes and he is also 1/2 hour from me so if you need to ship anything or want to donate , I will help as much as I can!

[shoooter]

I have a lot of these parts in my Sea container back in AB , I doubt I can get to them though & shipping would be tough , I have a number of starters ,alts, ecu , dist , oil pans , timing covers , 50 pullies ,spare headers , big block T bars & leafs , just not sure how to get them .

AB=Alberta? i could get some parts and send them with i will dig up too., I travel across the line and could get a better shipping rate in the states...

[Cuda Cody]

I have a lot of pullies so I'll get those out and find a set that will work.

[GranCuda1970]

I got a new idler arm in bag for a cuda some other stuff for a 440 I will look out in the garage and see whats avail from the list.

  I got a 1970 cast waterpump and housing, a small block 340  26" fan shroud that prolly wont fit.

[blown motor]

He is in Ann Arbor MI, I most likely will be driving down with a load of parts , maybe I could take what ever your donating down at the same time?   

Brad, when do you think this is going to happen? I'm going to Jackson MI in a few weeks which is just west of Ann Arbor. I can take a bunch of stuff and drop it off. Could also stop at Roseville and pick up parts. I'll be going right past there.

[brads70]

Brad, when do you think this is going to happen? I'm going to Jackson MI in a few weeks which is just west of Ann Arbor. I can take a bunch of stuff and drop it off. Could also stop at Roseville and pick up parts. I'll be going right past there.

If your going in a few weeks that is most likely sooner than I was thinking!