News:

  • Home
  • Help
  • Chat
  • Login
  • Register

    • « previous next »
    Pages: [1]

    Author Topic: 70 Barracuda trunk install advice  (Read 1346 times)

    Offline calicuda70

    • 2 evil 70's and 1 BAD 11
    • Jr. Member
    • **
    • Posts: 246
    70 Barracuda trunk install advice
    « on: August 19, 2013 - 06:38:41 PM »
    Hey guys need some advice I'm at the point where I can weld my trunk pan in and I wonder what's the best way to weld it in on the ground with the weight on the wheels or jacked up like I have it and up a jack under the axle to take up some of the weight? Any advice helps thanks

    Calicuda
    Logged
    70 'Cuda 5.7 Hemi protouring resto
    70 Challenger 360
    11 Challenger SRT8 392


    Offline FY1Cuda

    • Sr. Member
    • ****
    • Posts: 1493
    Re: 70 Barracuda trunk install advice
    « Reply #1 on: August 19, 2013 - 09:12:05 PM »
    I'd do it just like in your pictures--with the weight off of the springs.  Just a reminder to weld the gas tank braces on while the floor's off.  Hopefully you took lots of measurements around the tail panel before you removed it. Good luck with your project.
    Logged

    Offline Topcat

    • C-C.com Expert
    • ********
    • Posts: 15376
    • Member since 9/16/04
    Re: 70 Barracuda trunk install advice
    « Reply #2 on: August 19, 2013 - 09:25:22 PM »
    I agree. Wow! What a major resto!

    That is going to be a ton of welding and grinding to do.
    Good progress. Looking forward to seeing it as it develops.
    Logged
    Mike, Fremont, CA.

    Offline calicuda70

    • 2 evil 70's and 1 BAD 11
    • Jr. Member
    • **
    • Posts: 246
    Re: 70 Barracuda trunk install advice
    « Reply #3 on: August 19, 2013 - 10:24:53 PM »
    Quote from: FY1Cuda on August 19, 2013 - 09:12:05 PM
    I'd do it just like in your pictures--with the weight off of the springs.  Just a reminder to weld the gas tank braces on while the floor's off.  Hopefully you took lots of measurements around the tail panel before you removed it. Good luck with your project.

    Fy1cuda

    Oops on my part I didn't think to take measurement doh just started hacking but I left the Dutchman panel installed figuring that it would be the best place to start off by centering the tail panel since its the only original panel left plus I still have the original tail panel with some of the metal left from the old trunk
    Logged
    70 'Cuda 5.7 Hemi protouring resto
    70 Challenger 360
    11 Challenger SRT8 392

    Offline Edison1970

    • Jr. Member
    • **
    • Posts: 489
    Re: 70 Barracuda trunk install advice
    « Reply #4 on: August 19, 2013 - 10:54:14 PM »
    When I did mine, I put everything together with sheet metal screws.  Make sure everything lines up first.  Then take off the quarters and the tail panel and start welding the trunk pan.
    Logged

    Offline calicuda70

    • 2 evil 70's and 1 BAD 11
    • Jr. Member
    • **
    • Posts: 246
    Re: 70 Barracuda trunk install advice
    « Reply #5 on: August 19, 2013 - 11:05:57 PM »
    Quote from: Edison1970 on August 19, 2013 - 10:54:14 PM
    When I did mine, I put everything together with sheet metal screws.  Make sure everything lines up first.  Then take off the quarters and the tail panel and start welding the trunk pan.

    Yea I got the trunk screwed in maybe ill wait to line everything up 1st  then burn the trunk in
    Logged
    70 'Cuda 5.7 Hemi protouring resto
    70 Challenger 360
    11 Challenger SRT8 392

    Offline crocha617

    • Sr. Member
    • ****
    • Posts: 1700
    Re: 70 Barracuda trunk install advice
    « Reply #6 on: August 22, 2013 - 05:01:45 PM »
    Quote from: calicuda70 on August 19, 2013 - 11:05:57 PM
    Yea I got the trunk screwed in maybe ill wait to line everything up 1st  then burn the trunk in

    I would remove the word MAYBE from your sentence. You must assemble the whole rear of the car before you weld or you'll be sorry.
    Logged
    Pages: [1]
    « previous next »