Attn: Final parts list! Updated 6/26/14

[DMZ73]

Welcome Damon!! It was great to meet you! Loved wrenching with you on Saturday. I'm sorry I didn't get a lot of time to learn from you on the trans assembly. I would really like to gain more understanding of that puzzle someday.
I'll add the trans cover to the list.
Cooler and bracket would be great!


dmz73

[DMZ73]

Dan, I remember we needed a water pump housing bolt kit or I'd've put it on last Saturday and do you have bolts for the intake? A distributor holdown and bolt? Was there no coil wire in that dusty old Accell wire kit? Wiring separators? Throttle cable/return spring and spring bracket? Just some wee pieces I thought about. Damon, good to see you on here, buddy! Regards,Ian

Ian,
I have a dizzy hold down bracket and I think I have the bolt.
No throttle return springs
No throttle bracket
Need intake manifold bolts
Need water pump bolts
No trans kickdown rods- easiest: we are going with the Lokar kit.
Yes, still missing a coil wire! Argh!
Dan



dmz73

[blown motor]

Dan, we are using the blaster 2 coil correct? If you can get me a length on that wire I might be able to make on from leftover wire and boots I have from putting new wires on mine. I could also tap into a friend's leftovers. It would be bright orange. I also have a shabby blue coil wire that we could put a new end on if it's long enough. It's currently HEI at the coil.

[BIGSHCLUNK]

Milodon dipstick and ballast resistor sent today. 

[MEK-Dangerfield]

Dan,

 The distributor and voltage regulator shipped today to Andy's house.

  Mike

[p-zero]

 Hey Dan do you update the original post with the parts you still need? (This is Pete, Andy's neighbor.)

 I can get a bunch of parts, and rather quickly at that, so let me know.

[Chryco Psycho]

Still need the Oil Pump ?

[jimynick]

I've sent the intake bolts and return spring/bracket kit to Cathy. Summit said they'd ship tonight and arrive either Saturday or Monday; so we can stroke those off the list as well. 

[DMZ73]

Chryco- yes we do still need to oil pump


dmz73

[DMZ73]

I need that brake booster Pin and cotter pin for Andy's car. I can't find it in his box o goodies
Dan


dmz73

[Chryco Psycho]

Oil pump should be there shortly
 let me know it arrived Please
The brake linkage is a tough piece to find

[Bullitt-]

Ian,
I have a dizzy hold down bracket and I think I have the bolt.
No throttle return springs
No throttle bracket
Need intake manifold bolts
Need water pump bolts
No trans kickdown rods- easiest: we are going with the Lokar kit.
Yes, still missing a coil wire! Argh!
Dan



dmz73

Would these items solve the kickdown, bracket & return spring issues?
http://www.jegs.com/i/Lokar/625/KD-2727HT/10002/-1
http://www.jegs.com/i/Lokar/625/SRK-4000/10002/-1

directions  http://www.lokar.com/downloads/pdf-instructions/chrysler-kickdown.pdf

I'll send you the $ for you to order....PM me instructions

[p-zero]

I can check into the

I need that brake booster Pin and cotter pin for Andy's car. I can't find it in his box o goodies
Dan


dmz73

 I can check on those pins tomorrow. I have an assortment of cotter pins.

[blown motor]

Gas cap to be shipped today.

[DMZ73]

I can check into the  I can check on those pins tomorrow. I have an assortment of cotter pins.

Pete:
First: welcome!!
Second: I will need the shaft that works as  the brake booster linkage pivot. That part has the hole for the cotter pin.
Please take another look at the list. I update the list every time someone donates a part. It changes constantly.

I could probably use your mechanical skills more than anything when we put her together.

We still need wheel spacers
Some longer wheel studs,
A Nippon denso alternator pigtail
A mini starter
And some other bits and pieces.

Dan


dmz73